Patient lifts

Liko Mobile lifts: troubleshooting and error codes

The ServiceForge knowledge base holds 64 documented symptoms for the Liko Mobile lifts, with 74 ranked causes, 81 diagnostic checks with test points and expected values, and 0 error codes. Each symptom below shows its causes and the first check; the rest is one connection away. Connect ServiceForge to your AI

Symptoms

Emergency stop or electrical emergency-lowering device not functioning patient safety

Emergency stop out, but electrical emergency-lowering device does not function; lift arms up/down or base width in/out not responding

Ranked causes

1. Actuator or base motor cable position incorrect (occasional)
2. Output channel or motor fault (common)
3. Control box faulty (occasional)

First check

Reposition actuator and base motor cables

Test point: Actuator and base motor connections
Expected: Function restored after cable repositioning

1 more check with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

No charging function

Battery does not charge when charger connected; no indication of charging activity

Ranked causes

1. Poor contact between control box and battery (common)
2. Battery contact plates defective or broken (occasional)
3. Charging function faulty in control box (occasional)

First check

Verify battery and control box contact

Test point: Battery connection to control box
Expected: Green LED indicator light starts when battery reinstalled

4 more checks with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Operation panel functions not responding patient safety

Buttons on operation panel do not activate lift functions

Ranked causes

1. Emergency stop button activated (common)
2. Low battery capacity (common)
3. Faulty control box (occasional)

First check

Verify emergency stop is not activated

Test point: Emergency stop button
Expected: Button released (not pressed in)

2 more checks with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

All hand control functions not working patient safety

All buttons on hand control are non-responsive

Ranked causes

1. Emergency stop not released (common)
2. Defective hand control (occasional)

First check

Release emergency stop button

Test point: Emergency stop button
Expected: Button released and lifted

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Battery not charging caution

No charging function or battery not holding charge

Ranked causes

1. Poor contact between control box and battery (common)
2. Charger malfunction (occasional)

First check

Verify contact between control box and battery

Test point: Battery and control box contacts
Expected: Green LED lights automatically after battery insertion

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Golvo mast locking screws loose patient safety

Upper locking screws in mast are not tight or lower holes have screws installed (not permitted)

Ranked causes

1. Upper mast locking screws loose (common)
2. Screws installed in lower mast holes (not permitted) (rare)

First check

Verify upper mast locking screws are tight

Test point: Upper holes on mast where it connects to base
Expected: Both upper screws tight and secure

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Operation panel functions not working patient safety

Buttons on operation panel do not activate lift functions (CBL control unit models)

Ranked causes

1. Emergency stop not released (common)
2. Faulty control box (occasional)

First check

Release emergency stop button

Test point: Emergency stop button
Expected: Button released and lifted

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Abnormal noise from actuator caution

Actuator produces unusual sounds during operation

Ranked causes

1. Loose components or wear (unknown)

First check

Listen for abnormal noise during actuator operation

Test point: Actuator
Expected: No abnormal noise

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Actuator fasteners loose patient safety

Upper and lower actuator fasteners to the mast are not tight

Ranked causes

1. Fasteners not properly secured (common)

First check

Verify upper and lower actuator fasteners are tight

Test point: Upper and lower actuator fasteners to mast
Expected: Fasteners tight

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Base widening mechanism not functioning patient safety

Base does not open and close smoothly or reaches incorrect maximum and minimum positions

Ranked causes

1. Loose screws or nuts on base assembly (common)

First check

Inspect base widening mechanism

Test point: Base assembly
Expected: No visible damage or wear

2 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Battery takes longer than normal to charge or does not reach full charge

Charging cycle exceeds 5 hours or battery does not indicate full charge with green LED

Ranked causes

1. Battery aged or internal resistance increased (rare)

First check

Observe charging indicator LEDs during charge cycle

Test point: Battery charging LEDs
Expected: Lamps blink alternately yellow/yellow/green during charging; blinking green indicates charging complete

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Brakes do not hold patient safety

When brakes are locked, wheels still turn or housing swivels when lift is pushed

Ranked causes

1. Brake mechanism failure (occasional)

First check

Lock brakes and push lift horizontally

Test point: All wheels and swivel housing
Expected: Wheels do not turn and housing does not swivel

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Cable cover incorrectly mounted caution

Cable cover on CBL20 control unit not mounted properly

Ranked causes

1. Cable cover loose or displaced (common)

First check

Visually inspect cable cover mounting on CBL20

Test point: CBL20 control unit cable cover
Expected: Cable cover mounted securely and correctly

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Cable not properly inserted caution

Cables loose or disconnected from sockets

Ranked causes

1. Loose cable connections (common)

First check

Verify all cables are fully inserted

Test point: All cable connections
Expected: Cables firmly seated

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: LikoLight mobile lift welding inspection caution

Visual inspection of welding between arm and fastening device for deformation or cracks on LikoLight lifts.

Ranked causes

1. Welding defect or fatigue crack from loading cycles (rare)

First check

Visually inspect welding between arm and fastening device

Test point: LikoLight arm-fastening welded joint
Expected: No visible deformation or cracks in welding

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Control unit replacement affects usage tracking data

When Control Unit CBL or Jumbo Care is replaced, historical lift usage data (total Ah or As cycles) reflects only the new control unit, not the complete lift history

Ranked causes

1. Control Unit replaced; memory cleared or transferred incomplete (occasional)

First check

Review control unit replacement history in lift maintenance records

Test point: Service log and control unit serial number
Expected: Match serial number in documentation to verify original or replacement unit

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Deformities in sling bar attachment points patient safety

Attachment points show visible deformation or damage

Ranked causes

1. Stress, impact, or wear on attachment points (rare)

First check

Visually inspect attachment points

Test point: Sling bar attachment points (A)
Expected: No visible deformities or damage

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Emergency stop button not releasing patient safety

Red emergency stop button remains locked in pressed position and does not pop up

Ranked causes

1. Emergency stop button stuck or misaligned (unknown)

First check

Turn emergency stop button in direction of arrows

Test point: Red emergency stop button
Expected: Button releases and pops up to open position

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Excessive gap at M220/M230 fastening area patient safety

Gap at measured area exceeds maximum allowable distance on M220/M230 models

Ranked causes

1. Fastening screws loose or fastener wear (common)

First check

Measure gap at specified area (M220/M230 only)

Test point: M220/M230 fastening area
Expected: Gap does not exceed 3 mm (1/8 inch), max 3 mm

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Flexlink arm binds or does not lower freely patient safety

Link arm or flexlink arm does not move freely; binding detected when raising, lowering, or pivoting sling bar.

Ranked causes

1. Flexlink screw too tight (common)

First check

Manually raise sling bar and link arm with sling bar hanging lowest

Test point: Link arm
Expected: Freely raises and lowers without binding

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Flexlink arm binds or does not move freely patient safety

Link arm or flexlink arm sticks or resists movement when manually raised/lowered or pivoted

Ranked causes

1. Flexlink screw too tight (common)

First check

Manually raise sling bar and link arm

Test point: Link arm
Expected: Link arm lowers and raises freely

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Foot tray cracked or loose patient safety

Foot tray shows cracks or is not securely attached to metal frame (Sabina and RollOn models)

Ranked causes

1. Foot tray damaged or fasteners loose (occasional)

First check

Inspect foot tray for cracks

Test point: Foot tray surface
Expected: No visible cracks

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Golvo middle beam distances A and B not equal patient safety

Distances A and B on Golvo middle beam are not equal (symmetry check)

Ranked causes

1. Middle beam misaligned or bent (rare)

First check

Measure distances A and B on middle beam

Test point: Points A and B on Golvo middle beam
Expected: Distance A equals distance B

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Golvo stop screw lower not secured patient safety

K6S M8x16 screw on Golvo middle beam is not properly secured with nyloc nut

Ranked causes

1. K6S M8x16 screw loose or nyloc nut missing (occasional)

First check

Verify lower stop screw is secured

Test point: K6S M8x16 screw and nyloc nut in middle beam
Expected: Stop screw tight with nyloc nut

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Golvo stop screw upper not secured patient safety

M6x8 Ezloc stop screw on Golvo middle beam is not properly secured with square nut (Golvo produced from Dec 2014 or with replaced middle beam)

Ranked causes

1. M6x8 Ezloc stop screw loose or nut missing (occasional)

First check

Verify upper stop screw is secured

Test point: M6x8 Ezloc stop screw and square nut in middle beam
Expected: Stop screw tight with square nut

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Hand control buttons do not respond with emergency stop pressed patient safety

Hand control buttons remain inactive when emergency stop is engaged

Ranked causes

1. Normal operation - emergency stop engaged (common)

First check

Press emergency stop and attempt hand control button operation

Test point: Hand control buttons with emergency stop engaged
Expected: Hand control buttons have no effect on lift

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Hand control buttons not operating lift patient safety

Control panel functions work but hand control has no function

Ranked causes

1. Defective or broken battery contact plates in hand control (common)

First check

Visually inspect hand control battery contact plates

Test point: Hand control battery contacts
Expected: Contact plates intact and clean

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Hand control has no function but control panel works patient safety

Control box function is operational but hand control does not respond to commands

Ranked causes

1. Hand control battery contact plates defective or broken (common)

First check

Inspect hand control battery contact plates

Test point: Hand control battery contacts
Expected: Contact plates intact and properly positioned

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Leg widening play excessive (Sabina II only) patient safety

Horizontal movement of legs from inner position exceeds allowable limit

Ranked causes

1. Leg support pins or hinges worn or loose (occasional)

First check

With legs in inner position, push legs by hand in and out and measure total movement

Test point: Leg pivot assembly
Expected: 35 mm / 1.38 Inch total or less, <= 35 mm
Tools: Ruler or caliper

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Lift arm binds or does not move freely patient safety

Arm does not move smoothly through full lifting cycle without load; binding or restricted motion detected.

Ranked causes

1. Mounting screw too tight (common)

First check

Run lift arm through full cycle without load

Test point: Lift arm
Expected: Smooth motion without binding

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Lift arm or base width function not working patient safety

Lift arms do not move up/down or base width does not adjust in/out

Ranked causes

1. Actuator or base motor cable disconnected or reversed (common)

First check

Verify actuator and base motor cable positions

Test point: Actuator and base motor cable connectors
Expected: Cables in correct position for respective motors

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

LikoLight mobile lift has welding deformation or cracks patient safety

Visible deformation or cracks in welding between arm and fastening device on LikoLight model

Ranked causes

1. Fatigue, stress, or impact damage to welding (rare)

First check

Visually inspect welding on LikoLight lift

Test point: Welding between arm and fastening device
Expected: No visible deformation or cracks in welding

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Low battery capacity caution

Operating time noticeably shorter than normal; battery capacity below expected

Ranked causes

1. Battery aged or degraded (common)

First check

Press battery capacity button to check LED indicators

Test point: Battery capacity LED indicator
Expected: Green LED indicates >50% capacity; yellow indicates 25-50% or 0-25%

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Low battery capacity or short operating time

Battery operates noticeably shorter than normal; reduced runtime between charges

Ranked causes

1. Battery capacity degraded or battery aged (common)

First check

Check battery capacity indicator

Test point: Battery i button and LED indicators
Expected: Green light indicates more than 50% capacity; yellow light indicates 25-50% or 0-25%

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

M220/M230 sling bar gap excessive caution

Gap in M220/M230 sling bar area exceeds maximum allowed tolerance.

Ranked causes

1. Wear or deformation of sling bar or fastening points (occasional)

First check

Measure gap in sling bar area on M220/M230 lifts

Test point: Sling bar gap area
Expected: 3 mm (1/8 inch) or less, max 3 mm

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Mast holes deformed patient safety

Deformation of holes in mast detected, distance between sides unequal

Ranked causes

1. Mast holes deformed due to stress or impact (rare)

First check

Measure distance from cover hat to top of ear on each side

Test point: Mast holes (X¹ and X²)
Expected: X¹=X² ±1 mm/0.04 inch, ±1 mm

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Micro switch fault in LA31 caution

Micro switch malfunction in LA31 (Uno 200, Sabina 200 models)

Ranked causes

1. Defective micro switch in LA31 (unknown)

First check

Inspect micro switch using SB001 service box

Test point: LA31 micro switch
Expected: Micro switch functions properly
Tools: Service box SB001 with adapter cable

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Outer tube stuck during operation patient safety

Outer tube gets stuck at some positions when arm is at highest position

Ranked causes

1. Outer tube obstruction or wear (unknown)

First check

Pull outer tube to top and bottom positions

Test point: Outer tube
Expected: Outer tube moves smoothly without sticking

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Overload indicator lamp lit patient safety

Overload warning lamp illuminates during lift operation (Viking, Golvo models)

Ranked causes

1. Electric end stop failure (common)

First check

Run lift to full up and full down positions

Test point: Overload indicator lamp
Expected: Indicator lamp not lit

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Play between fork and wheel nut patient safety

Visible or detectable movement between castor fork and wheel fastener

Ranked causes

1. Wheel nut loose (common)

First check

Manually move wheel side to side while holding fork

Test point: Wheel nut connection to castor fork
Expected: No play; wheel moves only with fork

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

RollOn cushion cover damaged caution

Cushion cover on RollOn support shows rips or tears

Ranked causes

1. Cushion cover worn or damaged (occasional)

First check

Inspect cushion cover condition

Test point: Cushion cover surface
Expected: No rips or tears

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

RollOn support locking mechanism loose patient safety

Upper or lower locking knobs are not tight or back plate screws are loose (RollOn support)

Ranked causes

1. Locking knobs or plate screws not tightened (common)

First check

Verify upper and lower locking knobs are tight

Test point: Locking knobs on RollOn support
Expected: Knobs secure with no play

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sabina latches not mounted patient safety

Latches (C) on Sabina sit-to-stand lift are missing or not installed.

Ranked causes

1. Latches missing or not installed (rare)

First check

Visually inspect Sabina latches

Test point: Sabina lift latches (C)
Expected: Latches mounted and in place

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sabina lift hook screws and locking washers loose or missing patient safety

Lift hook fasteners are not properly tightened or are missing on Sabina sit-to-stand lift

Ranked causes

1. Fasteners loose due to vibration or inadequate initial assembly (occasional)

First check

Inspect lift hook screws and locking washers

Test point: Lift hook fasteners (B)
Expected: All screws and locking washers tightened

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sabina lift hook screws loose patient safety

Lift hook screws or locking washers on Sabina lift are not tightened; fastening is loose.

Ranked causes

1. Lift hook fasteners loose (occasional)

First check

Inspect and tighten lift hook screws and locking washers

Test point: Sabina lift hook fasteners (B)
Expected: All screws and locking washers tight

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sabina lift hooks are outdated design patient safety

Sabina sit-to-stand lift equipped with old design lift hooks instead of latest version.

Ranked causes

1. Lift hooks not upgraded to latest design (occasional)

First check

Visually compare lift hooks against latest design reference

Test point: Sabina lift hooks (A)
Expected: Latest design hooks installed

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sabina lift latches not mounted patient safety

Latches missing from Sabina sit-to-stand lift

Ranked causes

1. Latches missing or not installed (rare)

First check

Verify latches are mounted on Sabina lift

Test point: Latches (C)
Expected: Latches mounted on Sabina sit-to-stand lift

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sabina sit-to-stand lift has old design lift hooks patient safety

Lift hooks are old design instead of latest version

Ranked causes

1. Lift hooks not updated to latest design (occasional)

First check

Inspect lift hook design on Sabina sit-to-stand lift

Test point: Lift hooks (A)
Expected: Latest design lift hooks installed

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Service Light illuminates on Control Unit patient safety

Service Light at the Control Unit illuminates, indicating that thorough inspection is required

Ranked causes

1. Scheduled maintenance interval reached or lift usage thresholds exceeded (common)

First check

Verify Service Light status and reason for illumination

Test point: Control Unit display
Expected: Service Light illuminated or annual inspection due

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar attachment points deformed caution

Deformities or damage detected at sling bar attachment points; may affect alignment or fastening.

Ranked causes

1. Impact, overload, or wear damage at attachment points (rare)

First check

Visually inspect attachment points (A) for deformation

Test point: Sling bar attachment points
Expected: No visible deformation or damage

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar cover not attached caution

Sling bar cover is missing or not properly attached to sling bar on standard model

Ranked causes

1. Cover not installed or fasteners loose (occasional)

First check

Inspect sling bar cover attachment

Test point: Sling bar cover fasteners
Expected: Cover securely attached to sling bar

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar does not rotate freely patient safety

Sling bar rotates unevenly, wobbles, or spinning stops due to high friction or bearing issues

Ranked causes

1. Bearing friction or contamination (occasional)

First check

Rotate sling bar and observe movement

Test point: Sling bar bearings
Expected: Sling bar rotates freely without wobble or uneven rotation

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar does not rotate freely on bearings patient safety

Sling bar rotates unevenly, wobbles, or stops due to high friction; bearing rotation not smooth.

Ranked causes

1. Bearing friction or contamination (unknown)

First check

Rotate sling bar by hand and observe motion

Test point: Sling bar bearings
Expected: Smooth, even rotation without wobble, high friction, or stopping

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar latches not mounted or not falling back patient safety

Latches are missing from sling bar or do not fall back against the body when released.

Ranked causes

1. Latches missing or damaged (rare)

First check

Visually inspect both sling bar latches

Test point: Sling bar latches
Expected: Both latches mounted and falling back against sling bar body

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar latches not mounted or not functioning patient safety

Latches are missing, not mounted, or do not fall back against body of sling bar

Ranked causes

1. Latches missing or loose (occasional)

First check

Verify both latches are mounted and functional

Test point: Sling bar latches
Expected: Both latches mounted and fall back against sling bar body

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar not correctly fastened patient safety

Sling bar fastening is loose or inadequate; unit may move or shift during operation.

Ranked causes

1. Fastening bolts or screws loose (occasional)

First check

Check tightness of sling bar fastening bolts and screws

Test point: Sling bar fastening points
Expected: All fasteners tight and secure

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sling bar standard o-ring missing or mispositioned caution

O-ring is not present in center bolt groove or is not centered on SlingBar Standard model

Ranked causes

1. O-ring not installed or has shifted position (occasional)

First check

Inspect o-ring on SlingBar Standard

Test point: Center bolt groove
Expected: O-ring present and centered in groove

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

SlingBar Standard bearing rotation compromised patient safety

Unit does not rotate freely on bearings or latches are not functioning properly on standard sling bar

Ranked causes

1. Bearing contamination, wear, or loose latches (occasional)

First check

Rotate unit and verify bearing function

Test point: Sling bar bearings and latches
Expected: Unit rotates freely; both latches fall back against body

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

SlingBar Standard cover not attached caution

Sling bar cover is not attached or is missing from sling bar.

Ranked causes

1. Cover not attached, loose, or missing (rare)

First check

Visually inspect sling bar cover attachment

Test point: SlingBar Standard cover
Expected: Cover firmly attached to sling bar

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

SlingBar Standard does not rotate freely patient safety

SlingBar Standard unit does not rotate smoothly on bearings; uneven rotation, wobble, or high friction present.

Ranked causes

1. Bearing friction, contamination, or wear (unknown)

First check

Rotate SlingBar Standard by hand and observe motion

Test point: SlingBar Standard bearings
Expected: Smooth, free rotation without wobble or high friction

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

More symptoms

SlingBar Standard latches not mounted
SlingBar Standard o-ring missing or mispositioned
Wheel height out of specification (Sabina II only)
Wheels do not roll freely

4 more symptoms with ranked causes and checks are in ServiceForge. Connect ServiceForge to your AI

Community

0 fixes logged by technicians through their AI, with outcomes, for this model.

ServiceForge knowledge base record. Field-unverified unless technicians confirmed it. A teaching summary of the record, not a service manual. Export 2026-10-14.