X-ray systems · V108R02 family

Konica Minolta CS7: troubleshooting and error codes

The ServiceForge knowledge base holds 13 documented symptoms for the Konica Minolta CS7, with 16 ranked causes, 43 diagnostic checks with test points and expected values, and 3 error codes. Each symptom below shows its causes and the first check; the rest is one connection away. Connect ServiceForge to your AI

Symptoms

Calibration: AeroDR detector unevenness warning during setup radiation

Warning appears during calibration when narrow exposure fields or foreign objects detected; allows continuation and data calibration despite warning condition

Ranked causes

1. Grid or marker obstruction in field (common)
2. Collimator not covering full detector (common)
3. Incorrect SID (Source-to-Image Distance) setting (common)
4. Incorrect X-ray exposure parameters (common)

First check

Verify no grid or markers in exposure field

Test point: AeroDR detector area
Expected: Clear field with no obstructions

3 more checks with pass and fail actions, 4 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: AeroDR detector unevenness warning interpretation change radiation

Unevenness error classification changed to warning in calibration tool; warning no longer blocks calibration completion, allowing data acquisition despite detection of narrow fields or foreign objects

Ranked causes

1. Software update changed error handling behavior (common)

Calibration: AeroDR Generator Interface Unit firmware update

Update firmware of AeroDR Generator Interface Unit or AeroDR Portable RF Unit when device and updated versions differ

Ranked causes

1. Firmware version mismatch between device and update package (occasional)

First check

Select firmware file for import

Test point: [File import] button
Expected: Firmware file selected and displayed in [Firmware file] field

3 more checks with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: AeroDR Generator Interface Unit XG BOX settings high voltage

Configuration of X-ray synchronization, network parameters, board mapping, and detector control settings for AeroDR Generator Interface Unit or AeroDR Portable RF Unit

Ranked causes

1. Initial setup or reconfiguration of XG BOX parameters (common)

First check

Verify X-ray synchronization settings

Test point: [X-Ray Sync1] or [X-Ray Sync2] screen
Expected: Coordination size/orientation selected and Bit Assign information configured

8 more checks with pass and fail actions, 11 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: automatic low-resolution from high-resolution data radiation

Generate low-resolution sensitivity data automatically from high-resolution calibration

Ranked causes

1. Automatic generation of low-resolution sensitivity data (common)

First check

Select automatic calculation mode

Test point: [Automatic calculation from high resolution data] checkbox
Expected: Mode enabled

2 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: Prep-Delay Time Measurement for S-SRM linkage high voltage

Measurement of delay time from exposure switch activation to exposure room build-up for S-SRM linked systems (not used in Japan)

Ranked causes

1. S-SRM delay time calibration required (occasional)

First check

Start delay time measurement cycle

Test point: [Start] button
Expected: Measurement initiated and running

3 more checks with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: Sensitivity radiation

Calibrate REGIUS detector sensitivity to establish detection level calibration data.

Ranked causes

1. Detector sensitivity requires calibration (common)

First check

Determine if automatic generation from high-resolution data is available

Test point: Calibration data status
Expected: High-resolution calibration data present

1 more check with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: sensitivity for mammography cassette radiation

Adjust sensitivity factor and exposure dose for mammography cassette (87.5 μm, 43.75 μm)

Ranked causes

1. Sensitivity calibration required for mammography cassette (common)

First check

Select resolution for mammography cassette

Test point: [Resolution] field
Expected: 87.5 μm (Mammo Standard) or 43.75 μm (Mammo High)

2 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: sensitivity for PCM cassette REGIUS 210 radiation

Adjust sensitivity factor and exposure dose for PCM cassette (RP-5PM, RP-6M)

Ranked causes

1. PCM cassette sensitivity calibration required (common)

First check

Verify PCM plate type

Test point: Cassette barcode read
Expected: RP-5PM or RP-6PM plate identified

2 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: sensitivity for regular cassette radiation

Adjust sensitivity factor and exposure dose for regular cassette (87.5 μm, 175 μm) imaging

Ranked causes

1. Sensitivity calibration required for regular cassette (common)

First check

Select resolution for regular cassette

Test point: [Resolution] field
Expected: 175 μm (General Std) or 87.5 μm (General High)

2 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: Unevenness radiation

Perform unevenness calibration of REGIUS detector to correct for uneven response across the imaging plate.

Ranked causes

1. Detector plate unevenness requires calibration (common)

First check

Verify exposure parameters before calibration

Test point: X-ray generator setting
Expected: 80 kV fixed voltage

3 more checks with pass and fail actions, 6 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Sensor monitoring not available

System monitoring function for REGIUS detector sensors.

Ranked causes

1. Sensor monitoring access requested (unknown)

First check

Verify monitoring capability access

Test point: Monitoring tab display
Expected: Sensor Monitoring section visible on [Monitoring] tab

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Set QR sensitivity reference values

Configure low, standard, and high sensitivity QR values used for calibration

Ranked causes

1. QR reference value adjustment needed (occasional)

First check

View low sensitivity QR value

Test point: [Low] field
Expected: 125

2 more checks with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Error codes

Code	Meaning	Trigger	Severity
`00`	OK	FPD reboot completion	info
`Study is Already Performed in Another Console`	Study cannot be started because it was already performed elsewhere	Attempting to start a reacquired study on a different console	error
`Unknown error is happened`	Unspecified error during study deletion operation	During study deletion process	warning

Likely causes and actions for each code are in ServiceForge. Connect ServiceForge to your AI

Community

0 fixes logged by technicians through their AI, with outcomes, for this model.

ServiceForge knowledge base record. Field-unverified unless technicians confirmed it. A teaching summary of the record, not a service manual. Export 2026-10-14.