X-ray computed radiographies · IIP family

Fujifilm FCR: troubleshooting and error codes

The ServiceForge knowledge base holds 24 documented symptoms for the Fujifilm FCR, with 27 ranked causes, 60 diagnostic checks with test points and expected values, and 539 error codes. Each symptom below shows its causes and the first check; the rest is one connection away. Connect ServiceForge to your AI

Symptoms

QA-WS application installation fails or does not start

Installation errors occur or application fails to launch after installation, possibly with key registry errors on startup.

Ranked causes

1. Key registry not installed during initial setup (common)
2. Incorrect password entered during QA-WS installation (occasional)
3. DICOM key installed without reinstalling AP key (occasional)

First check

Verify key registry installation

Test point: Application startup screen
Expected: Application launches without key registry error message

1 more check with pass and fail actions, 3 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

QA-WS application not fully functional after installation

Application installed but DICOM or image functions unavailable or restricted.

Ranked causes

1. US image parameters not loaded for English AP (USA) (occasional)
2. DICOM Storage or Print Service not enabled (occasional)

First check

Verify correct language and region variant of QA-WS installed

Test point: Application About or Help menu
Expected: English AP (USA) if US parameters required, or appropriate regional version

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: CRT monitor artifact 1 (ringing, jitter, swimming, tailing)

Verify absence of visual artifacts including ringing, jitter, swimming, and tailing

Ranked causes

1. Artifact 1 verification procedure (unknown)

First check

Display Artifact 1 test pattern

Test point: Display Properties Background tab
Expected: Test pattern displayed

4 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: CRT monitor artifact 2 (inconsistency, flickering)

Verify absence of visual inconsistency and flickering artifacts

Ranked causes

1. Artifact 2 verification procedure (unknown)

First check

Display Artifact 2 test pattern

Test point: Display Properties Background tab
Expected: Test pattern displayed

2 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: CRT monitor chipping

Measure and verify no chipping exceeds 0.41 mm in center fluorescent face area

Ranked causes

1. CRT fluorescent face chipping inspection procedure (unknown)

First check

Inspect chipping in center fluorescent face area

Test point: Center of CRT fluorescent face (254 mm x 343 mm area)
Expected: No chipping above 0.41 mm, ≤

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: CRT monitor luminance

Measure and set CRT maximum luminance and uniformity across screen

Ranked causes

1. Luminance verification and calibration procedure (unknown)

First check

Display test pattern (Brightness)

Test point: Display Properties Background tab
Expected: All white pattern visible

3 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: CRT monitor resolution

Verify CRT display resolution meets specifications using test pattern

Ranked causes

1. Resolution verification procedure (unknown)

First check

Set luminance precondition (all white pattern)

Test point: Center of CRT screen
Expected: 250±10 cd/m2, ±10

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: Monitor distortion and tilt

Correct pin-cushion distortion and tilt on 21" CRT monitor

Ranked causes

1. Display distortion and tilt calibration procedure (unknown)

First check

Correct pin-cushion distortion

Test point: Knob e
Expected: No visible barrel or pin-cushion distortion

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: Monitor horizontal and vertical position

Adjust horizontal and vertical display position on 21" CRT monitor

Ranked causes

1. Display position calibration procedure (unknown)

First check

Set horizontal position

Test point: Knob b
Expected: Display centered horizontally

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration: Monitor horizontal and vertical size

Adjust horizontal and vertical display size on 21" CRT monitor

Ranked causes

1. Display size calibration procedure (unknown)

First check

Set horizontal size

Test point: Knob a
Expected: Display width appropriate

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

CRT monitor screen chipping detected caution

Visual defects or chips visible on the fluorescent display surface during quality assurance testing

Ranked causes

1. Manufacturing or handling defect in CRT screen (unknown)

First check

Visually inspect CRT monitor screen for chipping using test pattern

Test point: Center area of fluorescent face, rectangular region 254 mm x 343 mm
Expected: No chipping above 0.41 mm on average, 0.41 mm maximum average
Tools: Test pattern display, visual inspection

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

CRT monitor screen size or position incorrect

Monitor display dimensions or positioning does not meet specifications

Ranked causes

1. Monitor adjustment knobs not properly configured (common)

First check

Measure screen width (X dimension)

Test point: Horizontal dimension L1-L2
Expected: 360 mm, ±1%

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Delete items from COMP parameter maintenance screen

Remove selected items from the COMP prm-MT list box using double-click and delete dialog

Ranked causes

1. User selects item for deletion (unknown)

First check

Double-click item in list box

Test point: COMP prm-MT screen list box
Expected: Select Modification dialog appears

2 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Environmental settings lost after installing DICOM or AP key caution

System settings and configuration parameters not restored after key registry installation.

Ranked causes

1. Environmental settings not restored after key installation (common)

First check

Verify backup of environmental settings was created before key installation

Test point: System file directory or backup media
Expected: Backup files present from INSTALLATION section 7 procedure

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Host name not specified or requires change

Computer network name not configured or needs modification

Ranked causes

1. Host name not set or requires update (unknown)

First check

Verify host name is set

Test point: Network dialog > Identification tab > Computer Name
Expected: Desired host name configured
Tools: Windows network settings

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Image data lost after HDD replacement or Windows NT reinstall caution

Image data on D: drive becomes inaccessible or deleted when HDD is replaced or Windows NT is reinstalled.

Ranked causes

1. Image storage partition (D:) deleted during HDD or OS installation (common)

First check

Verify D: partition exists in Disk Administrator

Test point: Disk Administrator main window partition list
Expected: D: partition visible and formatted as NTFS

4 more checks with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Monitor display menu does not appear

Menu fails to display after HDD access lamp goes OFF on 21" CRT monitor

Ranked causes

1. Monitor brightness and contrast require adjustment (common)

First check

Verify HDD access lamp is completely OFF

Test point: HDD access lamp
Expected: Lamp OFF

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Network information not configured

Windows NT network settings not properly configured for system communication

Ranked causes

1. Network Identification and Protocols not configured (common)

First check

Verify network adapter installed

Test point: Network dialog > Adapters tab
Expected: 3Com EtherLink XL NIC (3C905B-TX)
Tools: Windows network settings

2 more checks with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Quit COMP parameter maintenance application

Close ComPrm.exe application with unsaved changes prompt if needed

Ranked causes

1. Application closure requested (unknown)

First check

Click CLOSE button on COMP prm-MT screen

Test point: COMP prm-MT screen CLOSE button
Expected: Application closes or unsaved changes dialog appears

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Save changes in COMP parameter maintenance

Save modifications made in COMP prm-MT screen without quitting the application

Ranked causes

1. Changes made requiring save (unknown)

First check

Click SAVE button on COMP prm-MT screen

Test point: COMP prm-MT screen SAVE button
Expected: Changes saved without exiting application

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Screen saver not configured to prevent monitor burnout caution

CRT monitor screen saver setting not enabled, risking phosphor burnout during idle periods

Ranked causes

1. Screen saver disabled or set to None (common)

First check

Verify screen saver type selection

Test point: Display Properties > Screen Saver tab
Expected: Blank Screen
Tools: Windows display settings

1 more check with pass and fail actions, 1 corrective action, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Software upgrade to version A02 required

System requires upgrade from A00 or A01 to A02 version including software installation, file copy, registry setup, image file conversion, and database restructuring

Ranked causes

1. Software version upgrade needed (unknown)

First check

Insert installation CD-ROM into drive

Test point: CD-ROM drive
Expected: Setup screen appears

11 more checks with pass and fail actions, 5 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

System startup time not optimized

OS loader wait time at startup not configured for reduced boot delay

Ranked causes

1. OS Loader show list timeout set to default value (common)

First check

Verify OS Loader wait time setting

Test point: System Properties > Startup/Shutdown tab > Show list for field
Expected: 5 seconds
Tools: Windows system settings

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

TCP/IP and IP address configuration incomplete

TCP/IP protocol and IP address settings not configured for network communication

Ranked causes

1. TCP/IP protocol not configured with IP address and subnet mask (common)

First check

Verify TCP/IP protocol selected and configured

Test point: Network dialog > Protocols tab > TCP/IP Properties
Expected: TCP/IP configured with valid IP address and subnet mask
Tools: Windows network settings

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Error codes

Code	Meaning	Trigger	Severity
`0709`	Software application error	Failure during equipment management from software	error
`0A09`	Application error – field portion failure	Occurs in exceptional portion locations	error
`0AD9`	Application error – error detection expected procedure	When expected procedure components occur	error
`0B09`	Application error – work token issue	When work token errors currently occur	error
`0C09`	Application error – initial portion issue	When portion locations of image management occur	error
`0CD9`	Executable process margin possible	Margin in executable process possible	error
`0D09`	Application error – equipment requirement	When equipment requirement equipment get properly managed	error
`0D90`	Application error – equipment management	When equipment management fails	error
`0DD9`	The External error – error detected in operable device	When error is detected in operable device	error
`0E09`	Application error – required function management	When required function management equipment get properly managed	error
`0ED9`	The External error – transmission idle	When transmission idle error occurs	error
`0F09`	Application error – management device	When management device gets properly managed	error
`0FD9`	The External error – transmission idle	When transmission idle error occurs	error
`0x0258`	Failure recovered, memory buffer network timeout	Normal structured processing could not be completed	error
`0x0359`	Failure to delivery, memory buffer network timeout	Network data delivery transmission failure during image processing input	error
`0x1152`	Time-out between various image managing commands	Timeout when multiple image receiving or transmitting commands occur during execution	warning
`0x121F`	Check other device status or reconnect external device	Command/network connection timeout to external network device during network reception	error
`0x1251`	Failure to start image transmission, image data timeout	Timeout of image data transmission start signal during image processing input	error
`0x135B`	Time-out during command reception network reception exception	Timeout during command/network reception when other network device or external device communication occurs	error
`0x136F`	Time-out in device network reception exception	Time-out during command reception in external network device with external device communication network connection	error
`0x1F52`	Socket function test failure on FCR R/I-F connection network function	When no response reception or error detection occurs during image input processing network reception when other network device communicates within E/I-F socket function connection network	error
`0x4317`	Failed reception exception (1) or failed trans-mission to SCM CPU from device interface (2)	When unexpected reception error or transmission failure from SCM CPU or when device interface device driver receives error/unexpected reception or transmission failure	error
`0x7258`	Failed severe receiver, memory buffer network timeout	Network buffer timeout during external device communication receiver function during image processing input	error
`0x7261`			unknown
`0x8500`	Installation complete, ROM-DC key execution exception	ROM-DC key execution or ROM-DC key installation cannot start	info
`0x8501`	Command definition and file error in command and file definition error	File definition error in command definition management or file name definition error in command management	error
`1709`	Software design error during sensor signal detection	Error occurs when managing sensor signals during design and control logic	error
`1901`	Software error on warming up	Detected during system warm-up	error
`1902`	FCR common error on system connection	System bus communication failure	error
`1903`	System management control failure	Detected during system operation	error
`1904`	Control connection failure between systems	System bus communication error	error
`190A`	Failed warning for system maintenance requirement	Maintenance interval exceeded	warning
`190B`	Communication error between system bus devices	System bus connection failure	error
`190C`	Message display error from system message	System bus operation failure	error
`190D`	Equipment required to system bus message retention failure	Equipment failure or bus message retention	error
`190E`	Detected error or system bus initialization	System bus item not functioning during operation	error
`1910`	Failed warning for system initialization event	System bus initialization event not occurring	warning
`1911`	Message display error from system bus	Message display system bus removal or failure	error
`1912`	Failed warning for maintenance or system operation	System maintenance not completed or operation prevented	warning
`1913`	Failed warning for system operation cancellation	System operation cancellation not complete	warning
`1915`	Application of soft ware patch for fuse F3 open	Fuse F3 open condition detected	error
`1916`	Application software write fault	Fault in applying application software	error
`1916A`	Memory controller error in control panel	Remote monitoring memory controller fault	error
`1916B`	GMIFI-E setup sensor error	Setup sensor not detected	error
`1916C`	Remote monitoring error in signal transmission	Signal transmission lost during control panel remote monitoring	error
`1916D`	GMIFI-E pair remote monitoring error	Permanent remote monitoring connection lost	error
`1916E`	GMIFI-E wire error	Wire damage or disconnection detected	error
`1916F`	GMIFI-E validity error with data transmission	Data not valid in transmission to FCR unit	error
`1917`	GMIFI-E storage error	Error detected in GMIFI-E storage	error
`1917A`	FCR pipeline error detection (no exception/error)	Error detected in FCR exception/pipeline during common initialization	error
`1917E`	GMIFI-E motor error detection, common memory issue	Motor monitoring in GMIFI-E encountered common memory error	error
`1917F`	GMIFI-E motor timing error on detection	Motor common memory check during common initialization fle-check	error
`1917O`	Management error during FCR exchange operation	Memory-related error in FCR memory management	error
`1918A`	Pipeline error exception detection for monitoring GMIFI-E	Error detection required during motor monitoring motor setup	error
`1918B`	Motor timing error (EOT) common memory setup	Common memory check required during air sensor monitoring setup	error
`1918C`	Air sensor error (EOT) common memory check	Common memory check required during air sensor monitoring setup	error
`1918D`	Monitoring error cannot occur, common memory error	Monitoring error during common memory check detector error	error
`1918E`	GMIFI-E common memory check error detector	Common memory check in GMIFI-E during motor error detector	error
`1918F`	GMIFI-E motor timing error detector	Motor common memory check during common fle-check detection	error
`1918O`	Motor event not detected in setup procedure	Memory initialization failure during common GMIFI-E check	error
`1919A`	FCR buffer error detection	FCR pipeline error detected during application software write fault	error
`1919E`	GMIFI-E monitoring error during motor error detection	Motor error encountered common memory initialization fle-check detection	error
`1919F`	GMIFI-E motor timing error on detection	Motor common memory check during common fle-check detection	error
`1957`	Image queue put up to new queue requires repair	Image queue management failure	error
`1958`	Image queue timeout error	Image queue processing exceeds time limit	error
`1959`	Image queue timeout error	Image queue processing exceeds time limit	error
`195A`	Image revise semaines invalid	Image revision parameter required for maintenance	error
`195B`	Application software patch for scanner window registry setting in data status	Registry setting failure during initialization	error
`195C`	Application software patch for window registry viewing in data status	Registry window viewing failure during initialization	error
`195D`	Channel Display invalid	Channel display parameter error	error
`195E`	Channel status invalid	Channel status parameter error	error
`195F`	Application software patch for initialization message not contacting the other endpoint	Initialization message queue error during system startup	error
`1960`	Application software patch for failure at parameter detect equipment element	Equipment parameter detection failure at equipment element level	error
`1961`	Application software patch for connection parameter memory element generation detect equipment element	Memory element generation detection failure during initialization	error
`1962`	Application software patch for retriever and connection element reset initialization reservation server	Initialization reservation service failure	error
`1963`	Image queue put up to new required file system management generator sub-bus management configuration require field equipment queue file receiving new only when image recovery fails	File system queue management failure during sub-bus management generation	warning
`1964`	Image revise processing sub-bus subsystem (Waiting for Host to commence useful transmit of error code Host ports)	Sub-bus processing error during host communication	error
`1965`	Application software patch for force across external transmit element external retain element (Waiting for Host to execute subsystem error at connection element and transmit management force required)	Sub-bus system transmit element force error during host management	error
`19A`	Detected error	Error condition detected during operation	error
`19B`	Detected problem error	Problem detected during operation	error
`19C`	Smmu exposure error	SCMU memory error on exposure attempt	error
`19C0`	Common condition identify error	Failed to identify common condition	error
`19D`	SCMU open error	SCMU failure to open or initialize	error
`19D0`	FCR-DMS initialization error	When FCR-DMS device fails to initialize properly	error
`19D1`	FCR-DMS common communication pipeline error	When FCR-DMS device experiences pipeline initialization failure	error
`19D2`	FCR-DMS protocol analysis error	When FCR-DMS device reports protocol or analysis failure	error
`19D3`	FCR-DMS memory management error	When FCR-DMS device has insufficient memory capacity	error
`19D4`	FCR-DMS header data error	When FCR-DMS device header data becomes corrupt or unavailable	error
`19D5`	FCR-DMS data pipe performance error	When FCR-DMS device pipe parameter data becomes corrupt or unavailable	error
`19D6`	FCR-DMS bearing mechanical error	When FCR-DMS bearing channel becomes damaged or misaligned during operation	error
`19D9`	FCR-DMS image data management error from file lost	When FCR-DMS device loses image data due to file error in working memory or corrupt property parameters	error
`19DA`	FCR-DMS image data management convert error	When FCR-DMS device image data format conversion fails or patient data becomes corrupt	error
`19E`	SCMU reset error	SCMU reset sequence failed	error
`19E0`	Error detected in pixel data no linearity	When FCR-DMS device pixel linearity validation fails during data acquisition	error
`19E1`	Error detected in image management convert data correctly	When FCR-DMS device fails to correctly convert imaging management data during process	error
`19E2`	Error detected in device receiver malfunction	When FCR-DMS device receiver component fails during data acquisition	error
`19E3`	Error detected in receiver data error wired	When FCR-DMS device wired receiver component has data transmission error	error
`19E4`	Error detected in assembly malfunction wired in data	When FCR-DMS device wired assembly component fails during data transmission	error
`19E5`	Error detected in event send notification	When FCR-DMS device fails to send notification event during operation	error
`19E8`	Error detected in event reset component test	When FCR-DMS device event reset component fails verification test	error
`19E9`	Error detected in receiver current output voltage supply acquisition in imaging management	When FCR-DMS device current output measurement fails in device receiver during imaging management	error
`19EA`	Error detected in excess pixel size reduced in imaging management	When FCR-DMS device pixel size reduction fails during imaging process with data management	error
`19EB`	Error detected in time-out completion when event receives	When FCR-DMS device receives time-out completion signal during event acquisition	error
`19EC`	Error detected in timer selection removed item	When FCR-DMS device timer selection item is removed or deselected	error
`19ED`	Error detected in test timer element removed	When FCR-DMS device test timer element component is deselected or removed	error
`19EE`	Error detected in receiver warning event with await	When FCR-DMS device receiver sends awaiting warning event during operation	error
`19EF`	Error detected in failed waiting event with timeout	When FCR-DMS device fails waiting event timeout during operation with file refresh on start	error
`19F`	SCMU close error	SCMU closure operation failed	error
`19F0`	Error detected in exclusive pixel ID identification list exclusion in receiver	When FCR-DMS device exclusive pixel list item is excluded during receiver configuration	error
`19F1`	Error detected in element deleted in image element	When FCR-DMS device image element component is deleted or deselected	error
`19F2`	Error in exclusive pixel item validation list	When FCR-DMS exclusive pixel item validation fails during data acquisition	error
`19F3`	Error in base data add specific pixel identification validation	When FCR-DMS device specific pixel validation fails during base data acquisition	error
`1D90`	The Transmission error – reserve device cancellation	When transmission errors occur that allow reverse reserve transmission	error
`2709`	Storage management error	Failure during software management from equipment	error
`29C0`	Print DICOM data configuration error	System cannot properly configure DICOM print settings	error
`29C1`	Printer connection lost or multiple mount required	System loses connection to DICOM printer or needs multiple mount operations	error
`29C2`	Error in print correction program	Print correction program fails or encounters configuration error	error
`29C4`	E-title formation error	System cannot properly form or configure E-title settings	error
`29C5`	Different valve count in image and image gammas	Valve count mismatch detected between image and image gamma settings	error
`29C6`	Error in print correction program due to ongoing condition	Print correction program error occurs; one condition persists from prior images	error
`29C7`	Error in failure of image full function	System loses full function capability of image processing	error
`29C8`	Image reference box sequence error; requires printer setup	System has image reference box sequence issue; requires new DICOM printer setup	error
`29C9`	Error in image gallery connection malfunction	System has connection issue with DICOM image gallery or DICOM module	error
`29CA`	Common-class error; visual verification event needed	System detects common-class error condition; visual verification and correction program needed	error
`29CB`	Error in configuration function management	System cannot properly configure function management settings	error
`29CC`	Error in image full function; system message return required	Image full function failure; system status return needed	error
`29CD`	Error causes items missing from DICOM module output	System detects items missing from DICOM module; either cause or status issue	error
`29CE`	No connection with DICOM module; disassembled connection status	System has no connection or disassembled connection with DICOM module	error
`29CF`	Error in XCO complete open function; DICOM module repair needed	XCO complete open function error; DICOM module requires repair or exchange	error
`29D0`	Error disassembled from DICOM module backup	System encounters error during DICOM module error disassembly from backup	error
`2D90`	The Transmission error – transmission missing	When transmission errors occur that allow checking when enabled	error
`3709`	Software completion error	Failure during software equipment management operation	error
`4709`	Memory capacity error	Memory capacity exceeded or invalid during system operation	error
`5709`	Data error or corrupt data base	Failure during data management software operation	error
`5D90`	Error detected – parameter retention	When parameter retention error detection when enabled for parameter setup output	error
`6709`	Network transmission error	Device network transmission failure or missing equipment service	error
`7709`	Management error class	Failure during management software operation	error
`8028`	Common error in corrective action	Occurs between corrective actions	unknown
`8029`	Error in initializing socket	Occurs between corrective actions	unknown
`802A`	Confirmation connecting films	Occurs between corrective actions with diagnosis of films	unknown
`802B`	Installation elevation variant	Corrective error received in installation settings	unknown
`803E`	Program error	Error in software application version	unknown
`85D`	Connector field tool error	During field tool detection	error
`8601`	Film analysis process occurs filter file character notation maintenance; film filter backlash set during film initialization	Occurs during film analysis process of filter file character notation; film character notation backlash set during film file initialization; may occur due to filter analysis process during film filter initialization file setup	error
`8709`	Cancel elegant connection error	Elegant connection cancel error during device service revision	error
`8C09`	Application error	Occurs when prerequisite conditions are met	error
`8F89`	Software corruption - parameter error	When parameter files become corrupted or invalid capacity exceeds memory limit	error
`9008`	Application software error	Firmware malfunction during operation	error
`9018`	Application software error	Firmware malfunction during operation	error
`9028`	Image processing output success error	During imaging output, on the other hand, user sees	error
`9048`	Application software error	Incoming filter error in filter property replacement error (error being seen in filter property)	error
`9058`	Application software error	Internal filter error, maintenance start data missing imaging start data at input imaging system maintenance, confirm error mission missing start data in input imaging system	error
`9068`	Application software error	Internal filter error in data management, confirm imaging management error in input imaging system (data management error in imaging system (occurred error on input imaging equipment))	error
`9078`	Application software error	Interlocking internal filter error, revise receiver messaging in receiver for all exchange filter requirements (reviser required)	error
`9088`	Application software error	Receiver messaging system malfunction error, new worker required in worker availability	error
`9098`	Application software error	Interlocking filter object error occurrence (Interlocking filter object error in filter object property)	warning
`90A`	Application software error	Error occuring to application software error code protocol (error due to filter mapper protocol mapping)	error
`90A8`	Application software error	Interlocking worker for filter mapper status/functionality required input mapper occurrence (reviser required)	error
`90B`	Application software error	Data driven from input imaging equipment restart (error running during input imaging equipment)	warning
`90B8`	Application software error	Transmission multiple filters detected (multiple filters detected in transmission error due to filter sensor in transmission error due to filter sensor transmission)	warning
`90C0`	Application software error	Error occuring to application 'hand-held field-hand-bus-system-message's (error of acquisition for the hand-held field-hand-bus-system-message's right success access)	error
`90C1`	Application software error	Error 'eraser base data success access' hand-held field-hand-bus-system (hand-held field-hand-bus-system (right success access) base data eraser during)	error
`90C2`	Application software error	Error 'imaging get' field-hand-bus-system (image get field-hand-bus-system) (right success access) base data	error
`90C3`	Application software error	Error occurrence 'router's imaging data' field-hand-bus-system (router's imaging data in imaging from field-hand-bus-system (right success access))	error
`90C4`	Application software error	Error occurrence 'togs get' field-hand-bus-system (togs get data imaging transition in data transmit field-hand-bus-system (right success access) has base data)	error
`90C5`	Application software error	Error occurrence 'togs finish' field-hand-bus-system (togs finish imaging from field-hand-bus-system (completing transition data) has base data)	error
`90C6`	Application software error	Error 'get' imaging 'get' field-hand-bus-system (from field-hand-bus-system (right success access) has require imaging get data 'get')	error
`90C7`	Application software error	Error 'delete' imaging 'deleted' field-hand-bus-system (delete field-hand-bus-system (has base data 'delete'))	error
`9114`	Extended examination/API application error	System maintenance requirement not received	error
`9115`	Common examination error	System failure in bus	error
`9117`	Cannot connect - apply application software	Memory failure encountered	error
`9118`	Cannot connect - apply application software	Channel status of the function	error
`9119`	Cannot connect - apply application software	Receiving by accessing message	error
`911A`	Cannot connect - apply application software	Equipment image initialization queue	error
`911B`	Failed - apply application software	Wait without image equipment initialization queue	error
`911D`	Cannot connect - apply application software	Equipment image deletion queue	error
`911E`	Cannot connect - apply application software	Equipment image modification queue	error
`911F`	Image processing error	System bus expected	error
`911F`	Cannot connect with connected host to which image is output	DTK returned error 'cannot connect to host'. Failed in request for connection	error
`9120`	Cannot connect - apply application software	Equipment image get maintenance code	error
`9121`	Cannot connect - apply application software	Received in get memory generation into queue	error
`9123`	Cannot connect - apply application software	Equipment image initialization queue	error
`9124`	Cannot connect - apply application software	Equipment image open on file queue	error
`9125`	Cannot connect - apply application software	Duplicate file queue failure backup queue control open door	error
`9126`	Cannot connect - apply application software	Equipment image still in file queue	error
`9127`	Cannot connect - apply application software	Equipment image still in file back queue in operation	error
`9128`	Cannot connect - apply application software	Received in get memory generation without queue	error
`9129`	Cannot connect - apply application software	Equipment image written in data queue	error
`912A`	Cannot connect - apply application software	Equipment image written in file back queue queue	error
`912A`	Image data confirmation from imaging procedure in application	Image data loss or invalid image data from imaging procedure	error
`912B`	Image reception of multiple required image transmission data	Image transmission from imaging data error	error
`912B`	Cannot connect - found error	Equipment error in found queue data queue	error
`912C`	Cannot connect - apply application software	Equipment display status queue in operation	error
`912C`	Error connection with common notification	Notification error during equipment connection	warning
`912D`	Cannot connect - apply application software	Equipment correct position in operation	error
`912D`	Equipment connection required for image detection	No connection to equipment for image transmission	warning
`912E`	Image receiving reject cases with image management	Image receiving rejection during imaging management	error
`9139A`	Apply power-on operation warning	Applied power-on operation	warning
`9139B`	Applied power-on operation warning	Applied power-on operation	warning
`9139C`	Error detected in file closing during error occurring announcement	File close error during announcement	error
`9139D`	Error detected in file getting during announcement	File get error during announcement	error
`9139E`	Error detected in file getting during closing announcement	File get error during closing announcement	error
`9139F`	Apply power-on operation warning for file lock control	File lock control error during power-on	warning
`9140`	Apply power-on operation warning for file lock control (Unused/Expected announcement)	File lock control error during power-on	warning
`9141`	Apply power-on operation without property support. FINF/FINP detected image imaging in system.	Image imaging detected without proper support	warning
`9142`	Apply power-on operation warning for component open file	Component open file error during power-on	warning
`9143`	Apply power-on operation warning for file open deletion contact	File open deletion error during power-on	warning
`9144`	Apply power-on operation warning for file locking image delete	File locking and image deletion error during power-on	warning
`9144B`	Apply power-on operation warning for one-time transmissions from device received coverage	One-time transmission data not received or coverage failure	warning
`9144C`	Apply power-on operation warning for file locking and image management control inhibition	File lock and image control problem during power-on	warning
`9144D`	Apply power-on operation warning for image size get	Image size determination error during power-on	error
`9144E`	Apply power-on operation warning for error detection during imaging transfer data	Error detected during image transfer or imaging startup data	error
`9144F`	Apply power-on operation warning (file lock) for file locking image management	File lock control error during imaging management	warning
`9150`	Apply power-on operation warning (undetermined) for file lock control component registration	File lock control component registration failure during power-on	warning
`9151`	Apply power-on operation warning for file log manner	File log management error during power-on	warning
`9152`	Apply power-on operation warning for file log open file	File log open file error during power-on	warning
`9153`	Apply power-on operation warning for file log writing data the file	File log writing data error during power-on	warning
`9154`	Apply power-on operation warning for memory control operation encountering memory encountered	Memory insufficient operation error memory encountered	warning
`91F4`	Application software failure on FCR interface	Detected during startup or operation	error
`91F5`	Unexpected error detected in image data memory	Detected during image processing or delivery	error
`91F6`	Data management error in output memory window	Detected during image output or storage operation	error
`91F7`	Data management error during FCR image remapping	Detected when remapping with new data assignment	error
`91F8`	Common communication error in momentum memory buffer	Detected during image acquisition or communication	error
`91FA`	Application software failure or messaging sensor detection	Software or sensor messaging failure during startup	error
`9207`	Receiver command exception or undefined request	Invalid or unrecognized command from receiver	warning
`9208`	FCR event failed to activate or maintain	Event activation failure or event maintenance loss	warning
`920A`	Receiver requires connection or cannot connect	Receiver cannot establish connection or connection lost	warning
`920B`	Event failure during maintenance or event absence	Maintenance event failed or event completely absent	warning
`920C`	Receiver monitoring failure for motion or image delivery	Monitoring system failed during multi-image transmission	warning
`920D`	FCR-DMS station failure during scene or receive initiation	Station communication failure or receive initiation failed	error
`920E`	Imaging FCR-DMS transfer or receive imaging failure	Station imaging transfer or scene receive failed	error
`9215`	FCR-DMS current status in application process	Detected during FCR startup or command process	info
`9216`	Application of waxproofing for FCR processor commonization	Data invalid during imaging procedure	error
`9217`	Multiple image receiving required during imaging management	Image data transmission error or incomplete image set	error
`9219`	Image exclusive setting to visible setting atlas	Image exclusion conditions detected	error
`9220`	FCR processor exclusivity of test settings	Exclusive visibility in image test	error
`9221`	FCR processor visual exclusivity test to visible setting atlas	Visual exclusivity settings invalid or test point atlas settings require definition	error
`9222`	Connect alert contact between holder and content placement	Contact connection error when content placement changed	warning
`9223`	FCR image receiver modification required	Image modification required when FCR image receiver changed	warning
`9224`	Equipment detection connection threshold	Equipment connection error detected during procedure	error
`9225`	FCR image receiver with attention attachment when multiple transmit frames	Image attachment error during multiple image frame transmission	warning
`9226`	Connect collation with memory capable validation	Memory capability validation error detected	error
`9231`	Occurrence in common accommodation phase	Common accommodation request during imaging transmission	error
`9232`	Collation contact with memory capable validation	Memory capability validation error	error
`9240`	RC maintenance component sensing required before RC initialization in formation.	RC component sensing procedure initiated	error
`9241`	RC maintenance component sensing required; starting RC maintenance in formation.	RC diagnostic/maintenance procedure initiated	error
`9242`	If it was not equipped to perform corpse decoding of RC maintenance component.	RC decoding/initialization procedure initiated	error
`9243`	If it was not equipped to perform corpse decoding of RC maintenance component.	RC maintenance decoding operation initiated	error
`9244`	If it was not obtainable the WA/IP reception in the error context.	RC error detection/reporting procedure initiated	error
`9245`	If it was not converted to obtain the RC maintenance error over interval.	RC maintenance interval conversion procedure initiated	error
`9246`	If it was not opened potential decoding failure in RC maintenance component.	RC component opening/access procedure initiated	error
`9247`	RC wired failure in maintenance of the RC component.	RC wired component maintenance procedure initiated	error
`9248`	If it was not closed RC maintenance in the RC component.	RC component closing/completion procedure initiated	error
`924A`	If it was required the RC maintenance component by failure configuration error decision.	RC failure configuration/initialization procedure initiated	error
`924B`	If it was not successful the occurrence of time item in RC maintenance.	RC time interval maintenance procedure initiated	error
`924C`	If it was not with equipment when RC maintenance configuration initializing other hosts.	RC maintenance with host equipment initialization procedure initiated	error
`924D`	If it was not containing error the RC maintenance in order to perform formation.	RC formation/initialization procedure initiated	error
`924E`	If it was not equipped to RC maintenance of item sensing notification failure.	RC item sensing/notification procedure initiated	error
`9251`	If it was not obtainable the RC maintenance area from an error occurrence.	RC area sensing/recognition procedure initiated	error
`9252`	If it was not obtained the table basis access base field of hands analysis.	RC data table access procedure initiated	error
`9253`	If it was not obtained the RC store error in order of maintenance perform formation base data.	RC error storage/retrieval procedure initiated	error
`9254`	If it was not stores other RC error in order of store of all devices formation.	RC error store synchronization procedure initiated	error
`9255`	If it was not stores other RC error data of store of all devices formation.	RC error data store synchronization procedure initiated	error
`9256`	If it was not obtained the RC error of the data updating from data provided.	RC data update/sync procedure initiated	error
`9257`	If it was not obtainable the RC maintenance area from a file error occurrence.	RC area file access procedure initiated	error
`9258`	If it was not obtainable the RC maintenance area from a file error occurrence.	RC area file access procedure initiated	error
`9259`	If it was not obtainable the table basis of access field hands for the file.	RC table file access procedure initiated	error
`929A`	Error occurred when not connected to Host	Connection loss to Host system	error
`929A0`	Image modality failure detected	Modality validation error in received image	warning
`929A1`	Image document code error	Document code validation failed	warning
`929A2`	FCR image ID error detected	Image ID validation failure	warning
`929A3`	Workorder number missing or invalid	Workorder validation failed	warning
`929A4`	Imaging module error detected	Module validation failure	error
`929A5`	Detector sorbitol value error	Detector sorbitol validation failed	warning
`929A6`	Image extended size error	Image size exceeds limit or invalid	warning
`929A7`	Image transfer failed, cannot connect	File transfer connection failed	error
`929A8`	Image process code error	Process code validation failed during transfer	warning
`929A9`	Scanning engine error detected	Engine validation failed during direction correction	error
`929AA`	Pixel value error during transfer	Pixel data validation failed	warning
`929AB`	INB module retrieval failure	INB module cannot be accessed or retrieved	error
`929AE`	Element A not specified in data	Required element A missing from dataset	error
`929AFA`	E-A title printer not detected	Printer communication failed or absent	warning
`929AFB`	Film dryer exists with N configuration	Film dryer present but configuration incorrect	warning
`929AFD`	Film detected error during session	Film detection failed or unexpected condition	warning
`929AFE`	Film dryer Box error on startup	Film dryer box initialization failed	error
`929AFF`	Film extended size error on startup	Film size validation failed during initialization	warning
`929B`	Error occurred when connected to Host	Error condition during Host communication	error
`929C`	Image retrieval failed during charging	Image not received or retrieved during operation	warning
`929D`	Error occurred during image management	Image management operation failure	error
`929E`	Error received from device recovery	Recovery operation failed	critical
`929F`	Error validation failed during operation	Validation check did not pass	warning
`929F3`	If it was not obtainable the WA/IP reception mechanism in order to perform diagnosis RC maintenance.	Equipment diagnostic procedure initiated	error
`9503`	External Communicator Sub System Detection Error (DICOM)	Distribution destination node set to DICOM but DICOM support is OFF in equipment, or no protocol set at destination node	error
`9556`	Invalid image data field	Connected host attempts to send image with illegal field value (date, time, modality, anatomical region, FCR ID, rows, columns, storage bit, expansion read size, compression, assigned bit, effective bit, data size, PIXEL, LINE, or scanning direction)	error
`9562`	Notified error to connected host	SOP class VIP of image to be sent is not set for network for DICOM of this equipment	warning
`9601`	DICOM printer resizing in image does not exist or there is no image in DICOM printer display format processing	Image information management in DICOM printer input information display format processing does not occur; image resizing function not found in printer input image format information	error
`9603`	Image value outstanding signal out other image signal it can reverse the output signal reverse the image value	The image value it can range from display format DICOM printer display format processing DICOM printer input information management to range outstanding image signal out to signal outstanding output	error
`9604`	DICOM printer setup failed title-E.A. printer DICOM with specification	When DICOM printer (new.tnirP.MOCI.D) did not get the specified setup with specification with title-E.A.	error
`9605`	DICOM printer identifying key setting identification number INB is numerical; Please make configuration with DICOM Printer configuration file connection contents of configuration management file setup management apparatus configuration management file startup configuration management file setup application management error instruction setup from DICOM Films (new.stliF) to execute films setup application setup management operation configuration file	When DICOM Films (new.stliF) could not get the specified setup with configuration management file setup management apparatus configuration management file	error
`9607`	DICOM printer Films creatic failure - It failed to get session from DICOM printer	Occurs when session transfer error occurs during DICOM printer operation or image management failure during DICOM printer session operation failure	error
`9608`	Film processing error - COM image management failure	Image management from COM box for film printing fails	error
`9609`	Film imaging management failure	Image imaging system fails for film processor COM box	error
`960A`	Film printing failure detected	Film printer output operation fails	error
`960B`	COM image management processing error	Digital COM image processing fails	error
`960C`	Film image processing failure - Defective image in film numbering	Film printing system detects defective output image	error
`960D`	Film E-A title designation error	Film E-A title not found in destination device configuration file	error
`960E`	Program error - existing numbered image failure in film numbering	Film system detects inconsistency in image version control	error
`960F`	Program error - Film numbering failure in image management	Film processing system fails on multiple image numbering or group operations	error
`9610`	Program error - Film system version failure	Film system detects version control or configuration mismatch	error
`9611`	Error occurrence in DCOM printer operations	Error status detected before correction in DCOM printer operation	error
`9612`	Program error - Multiple image numbering in film system	DCOM image management processing fails for common class image numbering	error
`9613`	Program error in configuration management of DCOM printer	Error in DCOM printer configuration execution or runtime management	error
`9614`	Program error - Common class error in DCOM printer configuration	Error in DCOM printer configuration with event view function	error
`9615`	Program error in system operation management	System operational error detected in same operation conditions	error
`9616`	Film output failure - No response from film processor	Film processor fails to respond to COM output request from DCOM box	error
`9617`	DCOM connection error - Connection not established with printer	DCOM box fails to establish connection with printer during setup	error
`9618`	Program error - COM XCP component failure in DCOM	System detects error in COM component operation	error
`9619`	Error feedback - Film system backup function failure (BSF-N CAUTION)	DCOM printer backup function error from secondary film system	warning
`961A`	Error feedback - Backup film system error (BBF-N ACTION)	DCOM printer backup system error with ACTION requirement	warning
`961B`	Program error - Image sizing error with MAG_TYPE and multi-film support	DCOM printer image sizing or magnitude type processing failure	error
`961C`	Program error - Film string image processing failure	Film image processing analysis failure or string management error in film printer	error
`961D`	Program error - Film mapping in bit-creation during film rotation	Error in film image mapping during bit-creation operation or film rotation	error
`961E`	Program error - Film assignment from film string in format	Film format string management error or film string assignment failure	error
`961F`	Program error - Film analysis process failure on film string image	Film image analysis process failure or error in film string configuration	error
`9620`	Program error - Film register miss-set in film string registration	Film registry failure or film string registration error during format operation	error
`9621`	Program error - Film fail condition in cable drawing during rotation	Film cable failure or film failure during rotation operation	error
`9622`	Program error - Warning status from BSF-N backup function in DCOM printer	DCOM printer backup function warning from BSF-N designation	warning
`9624`	Program error - Warning status BBF-N (TEST-BIN) from DCOM printer	DCOM printer backup warning from BBF-N (TEST-BIN) with configuration support	warning
`9709`	Network error	Equipment management transmission error or FIN/FINP required network work through	error
`9B10`	Item memory error detected	Item memory access or storage failure	error
`9B11`	Item memory get error	Failed to retrieve item from memory	error
`9B13`	Item create error	Failed to create new item in memory	error
`9B14`	Item event error	Item event sequence error	error
`9B15`	Item stop error	Item stop signal failed	error
`9B16`	Device receiver data validation error	Received data failed validation check	error
`9B17`	One-item system error	Single-item system error detected	error
`9B18`	Thereupon error	Unexpected operation occurred	error
`9C09`	Image management error	Image management from 9C09 occurs in 09C9 formations	error
`9F01`	Connected host rejected the connection request	DTK returned error 'other host rejected this request'. Failed in request for connection or transfer	error
`9F04`	Program error has occurred. Failed in DICOM file ID processing	Internal error detection during DICOM file processing	critical
`9F1F`	Program error has occurred. Failed during external DICOM request processing	Error in data during previous DICOM image input processing	critical
`9F50`	Program error has occurred. Failed in generation of DICOM threading	Internal error during DICOM input processing	critical
`9F60`	Could not send one of the specified images	Could not find information required for transfer or cue registration failed	error
`9F62`	Program error. Failed in DICOM data exchange, stream compilation, or image operations	No AE setting in DICOM configuration. AE information not transferable. Temporary file cannot be deleted	error
`9F62`	Network obstacle in image output processing. Failed in DICOM output association or output	No response from host to which image was input or output. DTK transfer text registration or connection request returned error during DICOM output	error
`A100`			unknown
`A1F5`			unknown
`A1F6`			unknown
`A1F8`			unknown
`A1F9`			unknown
`A1FA`			unknown
`A1FB`			unknown
`A1FC`			unknown
`B00`	Start-up timeout to process subsystem detection	Image Processing Subsystem does not complete startup within timeout period	error
`B02`	Insufficient memory recovery; equipment restart required	Occurs when memory efficiency insufficient for Image Processing Subsystem startup	error
`B03`	Image data files damaged; image data file deleted or corrupted	The image data files have been deleted with corrupted files detected during system operation or SysOp Data Management execution	error
`B060`	Application software write error	Detected during setup management	error
`B066`	Memory reconnection error	Detected during setup management	error
`B0C9`	Image management damaged or file image management error occurs	Detected during data management	error
`B0CA`	File image management error occurs	Image data corruption or system error	error
`B100`			unknown
`B12E`	Data revision device received image data	Image data retrieval or verification process	warning
`B12F`	Image data entered into device	Image data input process	warning
`B130`	Image information from device data management	Data retrieval or management failure	error
`B131`	Image information from device data	Data validation failure	error
`B132`	Application software connection error	Connection detection during software operation	error
`B133`	Application software connection error	Connection detection during software operation	error
`B134`	Application software connection error	Detected during application operation	error
`B135`	Application software connection error	Connection detection during operation	error
`B136`	Application software connection error	Connection detection during operation	error
`B137`	Specific memory steps error	Memory operation failure	error
`B138`	Application software write error	Detected during operation when data corruption occurs	error
`B192`	The image processing error occurs	Image processing subsystem failure or bus-to-bus transaction failure	error
`B1F5`	Application software write error	Detected in operating parameter set	error
`B1F6`	Application software write error	Detected in operating parameter set	error
`B200`			unknown
`B259`	Application software write error	Error detected in processor or core error during image processing	error
`B2BD`	Application software connection error	Detected operating error in OCX	error
`B300`			unknown
`B321`	Application software write error	Image management error detected	error
`B323`	Unexpected volume firmware error detected	Memory detection during function diagnosis	warning
`B400`			unknown
`B709`	Configuration initial maintenance error	Failure from transmission maintenance configuration	error
`B7CE`	Application software write error	Error detected in internal translation	error
`C004`	Start-up timeout to process subsystem detection one-time	Occurs one-time or multiple times during Start-up timeout phase	error
`C004`	Invalid parameter value (1)	When system detects invalid parameter during initialization	error
`C005`	Invalid parameter value (2)	When system detects invalid parameter during operation	error
`C006`	Cannot connect to database	When system fails to establish database connection	error
`C008`	Cannot modify database	When system fails to modify database contents	error
`C009`	Data database match failure	When system detects data mismatch between database and image management	error
`C00A`	Cannot connect to required database	When system fails to establish connection to database	error
`C00B`	No access to parameter requisites	When system cannot access required parameter configuration	error
`C00D`	Data value is invalid	When system detects invalid data value	error
`C00E`	Memory allocation failure	When system fails to allocate sufficient memory capacity	error
`C00F`	Multiple imaging management	When system processes multiple image management operations concurrently	warning
`C010`	Equipment exception record or image management image correlation issue	When equipment detects processing errors or image management equipment management issue (1) Firmware test equipment management issue with new equipment, if initial firmware in management cache, return equipment (2) Restore equipment cache.	critical
`C011`	Field initialization socket corruption or image management issue	When field management socket error detected	error
`C012`	Equipment exception record or memory file or circuit error	When equipment detects file memory or circuit failure	error
`C013`	Field failure built-in from management information formation	When system detects field management or formation management failure	error
`C014`	No capacity in hard disk or cache area	When system detects insufficient disk or cache capacity	error
`C015`	Field failure built-in from management database contents	When system detects field management or database management failure	error
`C-016`	Invalid imaging parameter	Imaging damaging parameter detected between imaging start and end	error
`C100`	No access to memory	System initialization on Windows startup; no success access cases	critical
`C101`	Inproper apparatus preparation	In-apparatus data setup performs data management information update	warning
`C200`	Field obtained handle on the window	Memory (window, device, ACT field catch value)	warning
`C202`	Failed recovery of image data files; image data file does not exist or has been deleted	Occurs when specific image data file procedures fail during recovery attempt	error
`C300`	Unexpected field on data information	Replacement field on memory (file image management replacement mapping parameter procedures)	critical
`C404`	No space partition in hard disk or hard disk partition errors frequently occur	Hard disk partition becomes full or hard disk partition errors occur frequently; frequent occurrence indicates recurring hard disk failures	error
`C709`	Setup storage error	Setup storage failure	error
`D-001`	Image damaged or not valid	Image damaging parameter detected during imaging process	error
`D-002`	File cannot be created	File creation failure detected	error
`D-003`	Invalid file setting detected	Invalid parameter detected in file settings	error
`D-004`	Invalid parameter value detected	Any invalid parameter value found in configuration when occurred	error
`D-005`	Key word invalid	Invalid key word detected in imaging initialization from imaging function	error
`D-006`	File cannot be deleted or removed	File deletion or removal failure detected	warning
`D-008`	Parameter data memory error	Parameter data memory error detected in window data initialization in system	error
`D-009`	Transfer entry error	Transfer entry failure to entry error detected during system initialization	error
`D-00A`	Transfer entry to entry error during system reset	Transfer entry error detected during system reset and initialization	error
`D-00C`	File position exception detected	File position exception detected in file position during imaging or in CONF_HIGH_ICON positioning	error
`D-00D`	File position exception detected in file position during CONF_HIGH_ICON initialization	File position exception detected in file position during CONF_HIGH_ICON initialization	error
`D-00E`	File position exception detected in CONF_HIGH_ICON initialization	File position exception detected in CONF_HIGH_ICON initialization positioning components	error
`D-00F`	SET function exception detected	SET function exception error occurs when required. Anomaly occurs when occurred.	error
`D-010`	GET function exception detected	Anomaly occurs when required during system initialization testing.	error
`D-011`	FPGA GSIS function exception detected during process initialization	Anomaly occurs when process error occurs in FPGA GSIS during initialization.	error
`D-012`	Calibration data validation error	Calibration data not found or invalid data validation error when occurred	error
`D-013`	File read error detected	File error detected in file read recovery	error
`D-014`	File write error detected	File write error detected in file recovery	error
`D-015`	Direction error to cartridge signal acquisition on registration	Image damaging parameter detected to registration is a registration. Imaging registration signal requires to apply signal acquisition for an important signal acquisition.	warning
`D-016`	Direction cart ridge movement error	Movement error in direction cartridge movement in cartridge occurred. Anomaly occurs when movement direction cartridge direction error has been detected. Different expectation from error.	warning
`D-017`	Parameter map view error	Parameter map view error in map view parameter map view error This will file setting occurs, perform error recovery procedures. File test on those files and repeat file test initialization.	warning
`D-018`	Parameter map view error	Parameter map view error in map view parameter map view error This will file setting occurs, perform error recovery procedures. File test on those files and repeat file test initialization.	warning
`D-019`	In formation information requires from registration signal from the registration	Anomaly occurs when occurred. Anomaly occurs when occurred in formation information registration signal.	warning
`D-01B`	Any extra configuration detected in title ellipse there the there the extra configuration circle been detected in title exception	Any extra configuration circle in title exception there the extra configuration circle been detected in title exception (defined time), Either extra configuration circle begun or title exception has begun.	unknown
`D050D`	Program error - Rotation manager requirement in formation operation	System requires rotation manager functionality in formation operation	error
`D050D`	Circuit device defect - ENE file validation	Environment file ENE designation validation failure in circuit device	error
`D050D`	Program error - Wiring code check with 16 or less number hold	Wiring code hex digit device circuit record validation failure	error
`D050D`	Program error - Identified determination value exceeding maximum numeration limitation	Identified numeration value exceeds maximum 129 determination in calibration	error
`D050D`	Program error - Rotation manager identification in ENE file	Rotation manager and manager number identification not found in formation	error
`D067`	Overprogramming PI test point pin; PPI overlay address addition overlay	During Field Tool arrangement overlay addition during Field Tool parameter arrangement (parameter overlay-add into field)	warning
`D068`	Overprogramming overlay hostname name attribute	During Field Tool overlay addition during Field Tool parameter modification during Field Tool setup with other device settings	warning
`D069`	No hostname attribute attached to pointing connection error	During Field Tool arrangement when attempting to attach hostname attribute to pointing connection error	warning
`D10`	Insufficient intensity (ITC) with 16-bit data	Detected during imaging acquisition	warning
`D1F5`	Apply configuration from recorded prior memory allocation state	Detected when prior memory allocation state not valid	warning
`D1F6`	Apply configuration error recovery from device receiver	Detected when device error recovery from prior configuration mismatch	error
`D1F7`	Apply configuration device coverage from API Window initialization	Detected when Window API error recovery application received trigger	error
`D1F8`	Apply configuration error event data base data transmission Failure	Detected error transmission failure in [Devices] and [Control Panel] status	error
`D1F9`	Initialize built-in initialization errors occurrence failure	Detected data base file correctly occurred initialization	warning
`D1FA`	Apply configuration error recovery from device receiver capability	Detected common receiver error (prior error management)	warning
`D1FB`	Detect parameter valid in valid parameter data in key data	Detected in key data valid parameter registered in BIOS data	warning
`D20`	Electronic A units deficiency	Condition during calibration or dynamic mode operation	warning
`D201`	Open configuration error file contents management cannot be opened in management file	File management error configuration file cannot be opened during file management configuration execution in setup startup of equipment	warning
`D202`	Configuration file overflow table data management file number in file management data	When file management error occurs after configuration file contents error conditions occur after file contents management error conditions	warning
`D203`	Inproper apparatus preparation circuit embedded Key rewording configuration management	Whenever Key rewording is different from description in file management file description (description difference) in file management file in apparatus startup equipment management setup	warning
`D21`	Gain arrangement correction needed (prone to error)	Detected during dynamic management correction operations	error
`D22`	Excessive electronic A unit values detected	Detected during calibration or filtering operations	warning
`D23`	Exception in corruption accumulation	Detected during exception management	error
`D24`	Required NUB enabling signal missing	Detected during NUB signal generation verification	error
`D25`	Callable collocation value set required	Detected during calibration or filtering operation timeouts	warning
`D26`	Multiple A-unit size fixed-title-E detection required	Detected during multi-element A units management feedback presence verification	error
`D27`	Size-coded value resizing required	Detected when size-coded value size-coded from alignment differs	warning
`D28`	Required imaging detection when size managed allegation required	Detected during size management allegation requirement verification	warning
`D29`	Remapping from allegation configuration management required	Detected when allegation configuration management needed	warning
`D2A`	Patching allocation value correction required	Detected when patching allocation value requires correction	warning
`D2B`	Combination with requirement mandates system requirements	Detected during combination and system requirement verification	warning
`D2C`	Size codec exception in filtering operation	Detected during size codec from filtering operation size-coded verification	warning
`D2E`	Multiple A-unit value filtration status requirements	Detected when multiple A-unit filtering operation status failed	error
`D2F`	Callable collection value correction required	Detected when callable collection value requires calibration correction	warning
`D30`	Multiple A units status required immediate correction	Detected when A unit status data fails maximum or min fixation	error
`D31`	Specific-titled A-unit problem existence failure	Detected when A-unit problems corrupt repair requirements from	error
`D32`	Error message issue in expectancy condition required	Detected during error message check occurrence	error
`D33`	System initialization required	Detected when system initialization failed	error
`D34`	Color imaging management failure detected	Detected when color imaging management failed in system	error
`D35`	Parameter error management occurred	Detected as error management corruption occurred	error
`D36`	Program error management on occasion corruption	Detected on error occasion management corruption detected	error
`D37`	Management color imaging failure in system detected	Detected when color imaging management failure in system	error
`D50B`	Allocation failure or palette allocation error	System detects insufficient memory allocation for color palette	error
`D50D`	Default information in formation default piece default two piece of default formation	System detects default formation condition	error
`D50E`	Image code size allocation error	System detects incorrect image code size	warning
`D50F`	Maximum number of size codes exceeded in limitation	System detects exceeding maximum size codes during operation	warning
`D510`	Image sizing requirement with gallery	System detects image sizing inconsistency	info
`D511`	Film marking specifications magification rate	System detects film marking rate inconsistency within specification	warning
`D512`	Film pattern replacement pattern replacement	System detects lift film pattern inconsistency	warning
`D513`	Film combination requirement with film specification	System detects film combination or image designation inconsistency	error
`D514`	Film combination orientation film size film information maximum designation exceeding	System detects maximum designation exceeded in film combination	error
`D515`	Error application software occurrence detected	An exception has occurred in the error mapping process	error
`D516`	Exception error occurrence detected in error mapping process	Any exception detected in one or more detection invalid key rows during error mapping process	error
`D517`	Valid key detection error	System detects invalid key rows during validation	error
`D518`	Error application software occurrence detected	System cannot open file or ENE value is not available or exclusive access not available process mapping applicable	error
`D51A`	Event setup maximum number of entries exceeding	System detects more than 1080 events in formation within event maximum limitation	error
`D51B`	Error application software occurrence detected	An exception has been detected in error mapping file entry point detection occurrence log processing	error
`D709`	Equipment stage capacity error	Stage equipment capacity create error	error
`E025D`	Specific error definition not fully readable due to OCR degradation	Unknown	unknown
`E026D`	Specific error definition not fully readable due to OCR degradation	Unknown	unknown
`E0604`	Application software error	Unknown	error
`E0605`	Application software error	Unknown	error
`E0606`	Application software error	Unknown	error
`E0607`	Application software error	Unknown	error
`E0608`	Application software error	Unknown	error
`E090`	Application software error	System bus error detection during operation	error
`E091`	Hardware/control panel connection error	Control panel failure or connection loss to main equipment	error
`E092`	Image management system initialization failure	System fails to initialize management classes during startup	error
`E093`	FCR reader connection error	FCR reader fails to establish connection to main unit	error
`E094`	Header authentication or workflow error	Workflow failure or header authentication issue detected	error
`E095`	Image file life-cycle management process error	File lifecycle management process fails during current operation	error
`E096`	Image file initialization in progress or incomplete	System detects incomplete image file initialization	error
`E097`	Image file initialization suspended or error in progress	System detects 'initiate complete' message or get glossary system error	error
`E098`	System bus 'trans' message error or header control failure	Header control connection failure or system bus error when 'trans' glossary detected	error
`E09A`	Register management device canine reverse operation required	System detects requirement to cancel register management device operation	error
`E09B`	Equipment name doesn't match or known issue encountered	Equipment name mismatch detected or equipment exclusion required	warning
`E09D`	Host management device required; reverse operation or configuration required	Candidate manager device canine reverse operation required; application software error during operation	warning
`E09E`	Image review system emergency or user-defined issue encountered	User-defined emergency detected when logging in; image management system issue; missing-user attribute	error
`E09F`	Work file lifecycle property deletion or registry management error	System detects lifecycle property deletion requirement; proper work item management needed	error
`E0C`	Initialize data failure	Data initialization process fails	error
`E0C08`	Application software error	Unknown	error
`E0C09`	Application software error	Unknown	error
`E0C0A`	Application software error	Unknown	error
`E0C0B`	Application software error	Unknown	error
`E0C0C`	Application software error	Unknown	error
`E0C0D`	Application software error	Unknown	error
`E0D0`	Old hold load data failure	Load old hold data fails	error
`E0D1`	Write wire data failure	Write wire data fails	error
`E0D2`	Performance error	Imaging processing performance error occurs	error
`E0D3`	CSV value failure	CSV parameter processing fails	error
`E0D4`	Fail discard data	Data deletion or discard fails	error
`E0D5`	Fail registration data file	File registration fails	error
`E0D6`	Find data validity failure	Data validity check fails	error
`E0D8`	Body data convert currently	Body code conversion occurs currently	error
`E0D9`	Machine image size detection	Machine image size code fails	error
`E0DA`	Lift file validation data	Uplift file manager formation fails	error
`E0DB`	Lift file validation data	Uplift file manager formation fails	error
`E0DC`	Machine size code sizing	Machine image sizing code fails	error
`E0DD`	IT wage full failure example	Wage IT code fullness issue	error
`E0DE`	IT wage full value failure	Wage IT code fullness value issue	error
`E0DF`	IT wage full value failure detail	Wage IT code fullness value issue pending detail	error
`E0F0`	Proprietary directory protocol establishment failure	System fails to establish proprietary directory protocol connection	error
`E709`	Management form requirement error	Failure getting equipment management form	error
`E-A19`	FCR device receiver malfunction	Receiver hardware detects error condition	error
`F709`	Setup form requirement storage error	Setup form requirement storage failure	error
`FA19`	SCMU device malfunction	Smart Card Memory Unit error condition detected	error

Likely causes and actions for each code are in ServiceForge. Connect ServiceForge to your AI

Community

0 fixes logged by technicians through their AI, with outcomes, for this model.

ServiceForge knowledge base record. Field-unverified unless technicians confirmed it. A teaching summary of the record, not a service manual. Export 2026-10-14.