Patient monitors

Agilent M1205: troubleshooting and error codes

The ServiceForge knowledge base holds 117 documented symptoms for the Agilent M1205, with 300 ranked causes, 173 diagnostic checks with test points and expected values, and 202 error codes. Each symptom below shows its causes and the first check; the rest is one connection away. Connect ServiceForge to your AI

Symptoms

BIS module INOP with specific error messages patient safety

Monitor displays INOP message and/or alarm indicator for BIS module with specific fault codes

Ranked causes

1. BIS module unplugged (common)
2. BIS module hardware malfunction or overcurrent (common)
3. BIS Engine not connected (common)
4. BIS Engine software incompatible (occasional)
5. BIS Engine hardware malfunction (occasional)
6. DSC not properly connected (occasional)
7. DSC hardware malfunction or PIC faulty (occasional)
8. DSC incompatible with BIS Engine (occasional)
9. BIS Sensor hardware malfunction (occasional)
10. BIS Sensor not properly connected (occasional)
11. Unsupported or unknown Sensor type connected (occasional)
12. Sensor expired due to overuse (occasional)

21 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

CO2 module INOP messages displayed

CO2 parameter displayed but one or more INOP alarm messages appear; examples include CO2 UNPLUGGED, CO2 EQUIPM MALF, CO2 NO TRANSDUCER, CO2 FAILED CAL, CO2 SENSOR WARM UP, etc.

Ranked causes

1. Transducer malfunction or module failure (common)
2. No transducer connected (common)
3. Calibration failed or aborted (common)
4. Transducer warming up (occasional)
5. Calibration in progress (occasional)
6. Calibration mode set but not started (occasional)
7. CO2 value out of calibration range (occasional)
8. ETCO2 value exceeds display scale (occasional)
9. Sidestream flow too low (occasional)
10. Sidestream tubing occlusion (occasional)
11. Sidestream pump malfunction (rare)
12. Sidestream pump auto-shutdown after apnea detection (occasional)

First check

Run CO2 module self-test

Test point: Self-test menu or diagnostics
Expected: Test numerics read exactly as listed; no failures

12 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

SpO2/Pleth INOP with waveform display issue patient safety

Module shows INOP message but waveform may appear; specific fault codes indicate transducer, signal, or measurement issues

Ranked causes

1. No transducer connected (common)
2. Malfunction in transducer or module (common)
3. Module unplugged from rack (occasional)
4. Erratic SpO2 measurements (common)
5. Noisy signal from patient movement or EMI (occasional)
6. Ambient light or cable-induced EMI interference (occasional)
7. Pulse too weak or non-pulsatile (occasional)
8. Transducer displaced during auto wave fixing (occasional)
9. SpO2 or PLETH transducer defective (occasional)

First check

Perform SpO2/Pleth Module Self-Test

Test point: Module self-test procedure
Expected: Test numerics match listed values exactly

1 more check with pass and fail actions, 9 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Temperature module not displaying or shows repeated INOPS patient safety

TEMP module fails to display readings or generates repeated INOP status messages on patient monitor

Ranked causes

1. Temperature probe not connected to module (common)
2. TEMP parameter disabled (common)
3. TEMP numeric display disabled (common)
4. Too many TEMP modules installed (occasional)
5. Poor module-to-rack connection (occasional)
6. Faulty rack slot connector (occasional)
7. Faulty satellite rack-to-function box cable (occasional)
8. Defective TEMP module (occasional)
9. Faulty rack or rack interface card (occasional)

First check

Verify temperature probe is physically connected

Test point: TEMP module connector
Expected: Probe connected

7 more checks with pass and fail actions, 9 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

C.O. module not responding or displaying error indicators

Visual indications or repeated INOP messages displayed for the Cardiac Output module; no response from module.

Ranked causes

1. C.O. Interface Cable or catheter not connected (common)
2. C.O. parameter or numeric display not enabled (common)
3. Multiple C.O. modules plugged in simultaneously (occasional)
4. Loose connection on module or rack interface (common)
5. Module not properly seated or faulty module slot connector (occasional)
6. Faulty Satellite Rack to function box cable (occasional)
7. Defective C.O. module (occasional)
8. Defective rack or rack interface card (occasional)

First check

Verify C.O. Interface Cable connection

Test point: C.O. Interface Cable connector
Expected: Cable fully seated to module

9 more checks with pass and fail actions, 12 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

CO2 module not recognized

CO2 parameter or numeric display missing or module shows no signs of operation; LED does not light up when module plugged in

Ranked causes

1. No transducer connected to module (common)
2. CO2 parameter or numeric turned off (common)
3. Multiple CO2 modules plugged in (occasional)
4. Module-rack connection loose (occasional)
5. Rack slot connector faulty (rare)
6. Satellite Rack to function box cable defective (rare)
7. CO2 module defective (rare)
8. Rack or rack interface card defective (rare)

First check

Verify transducer connected to module

Test point: CO2 module transducer connector
Expected: Transducer physically present and seated

7 more checks with pass and fail actions, 8 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Pressure module unresponsive or missing parameters

Pressure parameters or numerics not displayed; module shows no status indication or LED not lit

Ranked causes

1. No transducer connected to module (common)
2. Pressure parameter or numeric is turned off (common)
3. Too many pressure modules connected (occasional)
4. Module connection intermittent or loose (common)
5. Rack slot connector faulty (occasional)
6. Satellite Rack to function box cable faulty (rare)
7. Pressure module hardware defective (occasional)
8. Rack or rack interface card defective (rare)

First check

Verify transducer presence

Test point: Module inlet port
Expected: Transducer physically connected

7 more checks with pass and fail actions, 9 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

ECG/RESP module INOP status lights or module unresponsive

Module fails to light green LED on insertion or shows INOP messages for ECG/RESP parameters; module not functional in rack.

Ranked causes

1. Missing or disconnected trunk cable and lead set (common)
2. ECG and RESP parameters not enabled (common)
3. Multiple ECG/RESP modules installed (occasional)
4. Module or rack connector fault (occasional)
5. Defective module slot or rack (rare)
6. Defective ECG/RESP module (occasional)
7. Defective rack interface card (rare)

7 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Module self-test displays abnormal values

Module self-test produces test waveforms or numerics that do not match expected values for the patient category

Ranked causes

1. ECG module malfunction (rare)
2. Pressure module malfunction (rare)
3. SpO2/Pleth module malfunction (rare)
4. Cardiac Output module malfunction (rare)
5. tcpO2/tcpCO2 module malfunction (rare)
6. ETCO2 module malfunction (rare)
7. Temperature module malfunction (rare)

First check

Verify ECG module test heart rate in ADULT mode

Test point: Monitor display
Expected: 100 bpm

9 more checks with pass and fail actions, 7 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Pressure module self-test failure with INOP messages

Module displays self-test numerics that do not match specified values; INOP message persists with specific cause code

Ranked causes

1. <Px> UNPLUGGED (common)
2. <Px> NO TRANSDUCER (common)
3. <Px> EQUIP MALF (occasional)
4. <Px> ZERO + CHECK CAL (occasional)
5. <Px> OVERRANGE (occasional)
6. CPP CHECK SOURCES (occasional)
7. CPP CHECK UNITS (occasional)

First check

Perform module self-test

Test point: Self-test numerics display
Expected: Self-test numerics match exactly the listed specification values

1 more check with pass and fail actions, 9 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Printer not available or malfunction status message

Monitor displays 'No Printer Available' or 'Printer Malfunction' message

Ranked causes

1. Printer not connected to monitor (common)
2. Printer out of paper (common)
3. Printer power off (common)
4. Printer configured incorrectly (occasional)
5. Wrong printer setup in Configuration Mode (occasional)
6. Printer hardware malfunction (rare)
7. RS232 interface defective (rare)

First check

Verify printer RS232 cable connection

Test point: RS232 connector
Expected: Cable firmly seated and secure

3 more checks with pass and fail actions, 8 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

SpO2/Pleth module not recognized or offline patient safety

No module indication on display, INOP messages shown, or module LED does not light after insertion

Ranked causes

1. No transducer connected (common)
2. SpO2/Pleth parameter or numeric not enabled (common)
3. Too many SpO2/Pleth modules in same rack (occasional)
4. Faulty module connector or slot (occasional)
5. Defective satellite rack cable (occasional)
6. Defective SpO2/Pleth module (occasional)
7. Defective rack or rack interface card (rare)

First check

Verify transducer connection

Test point: Module transducer port
Expected: Transducer connected and seated

5 more checks with pass and fail actions, 8 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

BIS module shows error indicators or repeated INOPS patient safety

BIS module displays fault messages or INOP (inoperative) indicators on monitor screen

Ranked causes

1. BIS module unplugged or disconnected from rack (common)
2. BIS Engine not connected or Module Cable defective (common)
3. Rack connector faulty (occasional)
4. Satellite Rack cable faulty (occasional)
5. BIS module hardware defective (occasional)
6. Rack or rack interface card defective (rare)

First check

Verify BIS Engine, DSC and Sensor connections

Test point: BIS module connectors
Expected: All devices connected

8 more checks with pass and fail actions, 6 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Flat Panel backlight fails to light

Display backlight does not illuminate. May indicate cable, converter, or panel assembly failure.

Ranked causes

1. Cable connecting System Board to CDCI Board or Display Driver Board is defective (occasional)
2. Cable connecting CDCI Board to Flat Panel Adapter Board is defective (occasional)
3. Cable connecting Flat Panel Adapter Board to Flat Panel is defective (occasional)
4. Converter Board is defective (occasional)
5. Flat Panel assembly is defective (occasional)
6. Backlight is defective (occasional)

Blood Analysis module not operational

Module fails to operate or displays INOPS message; 2 green LEDs do not light after re-plugging

Ranked causes

1. Module connector faulty or module not seated (common)
2. Rack slot connector faulty (occasional)
3. Cable from Satellite Rack to function box faulty (occasional)
4. Blood Analysis module defective (occasional)
5. Rack or rack interface card defective (occasional)

First check

Verify parameter is enabled

Test point: Blood Analysis parameter setting
Expected: Parameter turned on

6 more checks with pass and fail actions, 7 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Display contrast or brightness not adjustable

Contrast adjustment knob (V24) or brightness adjustment (V24C/V26C/V24CT/V26CT) fails to change display

Ranked causes

1. Potentiometer assembly failure (common)
2. Flat Panel Adapter Board defective (occasional)
3. Ribbon cable connecting CDCI Board to Flat Panel Adapter Board faulty (occasional)
4. Flat Panel cabling defective (occasional)
5. Flat Panel assembly failure (occasional)

60V LED off or flashing

The 60V power supply LED indicator on the power supply is not illuminated or is flashing

Ranked causes

1. Power supply failure (common)
2. Internal 60V cable faulty or disconnected (occasional)
3. Internal 60V connector problem (occasional)
4. Short circuit in plug-in rack or parameter modules (occasional)

First check

Unplug rack from monitor

Test point: Plug-in rack connector
Expected: 60V LED should go off or stop flashing if short is in rack

1 more check with pass and fail actions are in ServiceForge. Connect ServiceForge to your AI

Backlight fails to light

Flat Panel display backlight does not illuminate when power is applied

Ranked causes

1. Cable connecting System Board to Flat Panel Adapter Board faulty or disconnected (common)
2. Flat Panel Adapter Board failure (occasional)
3. Cable connecting Flat Panel Adapter Board to Flat Panel faulty (occasional)
4. Backlight failure (occasional)

First check

Check 12V LED on power supply

Test point: Power supply LED indicator
Expected: 12V LED light is on

Blank display screen

Display shows no output or content

Ranked causes

1. Display brightness reduced by overheating from room temperature or nearby equipment (occasional)
2. Flat Panel Data Cable to System Board broken or disconnected (common)
3. Backlight inverter power supply fails (occasional)
4. Contrast or Brightness Control Assembly fails (occasional)

4 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Display is blank

Display screen shows no image or information

Ranked causes

1. No 12 volts present in instrument, contrast control not adjusted correctly, or backlight failed (common)
2. Flat Panel Data Cable disconnected or broken (occasional)
3. Backlight inverter power supply fails (occasional)
4. Contrast or Brightness Control Assembly fails (occasional)

6 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Flat Panel display shows no image (blank or black screen)

Screen appears totally black or blank despite power-on. Backlight may or may not be on.

Ranked causes

1. Backlight is off (common)
2. Power supply (+5V), System Board, DSPC Board, or Display Driver Board is defective (occasional)
3. Flat Panel assembly is defective (occasional)
4. Cables between boards are defective (occasional)

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

Module does not power on or LED does not light

After unplugging and re-plugging tcpO2/tcpCO2 module, green LED does not light up or parameter displays are absent.

Ranked causes

1. Faulty module slot connector (occasional)
2. Defective satellite rack to function box cable (occasional)
3. Defective tcpO2/tcpCO2 module (occasional)
4. Faulty rack or rack interface card (occasional)

First check

Green LED lights after module re-plug

Test point: Module LED indicator
Expected: LED lights

3 more checks with pass and fail actions, 4 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

NBP module not responding

No LED indication on NBP module after insertion or green LED not lighting

Ranked causes

1. Module connector contact failure (occasional)
2. Faulty satellite rack to function box cable (occasional)
3. NBP module is defective (occasional)
4. Rack or rack interface card failure (occasional)

First check

Ensure NBP parameter and numeric are enabled

Test point: Monitor display
Expected: NBP parameter and numeric display enabled

7 more checks with pass and fail actions, 5 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Power supply LED status indicators extinguished or abnormal caution

One or more LEDs on power supply assembly (visible through LEFT air vent) are not illuminated when they should be, or fuse blown suspected.

Ranked causes

1. LEFTMOST (AC Power) LED extinguished - Fuses F1, F2 (AC fuses) or F6 (18V fuse) blown (common)
2. MIDDLE (+5Vdc logic) and RIGHTMOST (12V) LEDs extinguished (occasional)
3. Only RIGHTMOST LED (+12V/60V) extinguished, MIDDLE LED on (occasional)
4. Only MIDDLE LED extinguished (occasional)

First check

Turn off power and remove front housing

Test point: Power supply assembly
Expected: Access to power supply and fuses

1 more check with pass and fail actions, 18 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

System Board fault indicators abnormal

Status LEDs on System Board indicate fault in Application Processor, Utility Processor, or SDN subsystem

Ranked causes

1. SDN subsystem reset error (occasional)
2. Application Processor system error (occasional)
3. Utility Processor system error (occasional)
4. System Board power loss (occasional)

First check

Observe SDN LED status

Test point: SDN Indicator LED on System Board
Expected: Should be OFF during normal operation

2 more checks with pass and fail actions, 4 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Temperature module INOP with specific error code patient safety

TEMP module generates specific INOP messages indicating the nature of the malfunction

Ranked causes

1. TEMP module unplugged from rack (common)
2. Temperature probe disconnected from module (common)
3. Temperature out of measurement range (occasional)
4. TEMP module hardware malfunction (rare)

First check

Perform temperature module self-test

Test point: TEMP module self-test numeric output
Expected: Exactly matches listed value in self-test procedure

1 more check with pass and fail actions, 4 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

5V/12V LEDs off or flashing caution

The 5V and/or 12V power supply LED indicators are not illuminated or are flashing, indicating overload or short circuit

Ranked causes

1. Power supply failure (common)
2. Short circuit on System Board or after power supply (common)
3. Short circuit on Flat Panel circuitry (occasional)

First check

Disconnect power supply to System Board 5V/12V ribbon cable

Test point: 5V/12V ribbon cable connector
Expected: 5V and 12V LEDs should remain off if power supply problem, or turn on if short is downstream

Battery or battery charger circuit suspected as faulty patient safety

Battery charging issue suspected; battery voltage measurement needed. For battery-backed operation troubleshooting.

Ranked causes

1. Battery over-discharged (voltage below 9 Vdc) (occasional)
2. Battery voltage between 9 and 14.7 Vdc (occasional)
3. Battery voltage absent; fuse F7 or F8 blown (occasional)

First check

Connect monitor to AC power and observe leftmost LED is illuminated

Test point: Power supply AC input
Expected: Leftmost LED illuminated

3 more checks with pass and fail actions, 5 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Display shows all white or deep blue without contrast control response

Monochrome screen is either all white or deep blue and does not change with movement of contrast control thumbwheel

Ranked causes

1. Flat Panel contrast circuit on Flat Panel Adapter Board failure (common)
2. Contrast control potentiometer failure (occasional)
3. Contrast circuit cabling defective (occasional)

Display shows no image with adjustable contrast

Monochrome screen can be adjusted in brightness via contrast control but no display appears

Ranked causes

1. System Board failure (occasional)
2. Flat Panel assembly failure (occasional)
3. Display cabling defective (occasional)

Equipment malfunction with INOP messages patient safety

Task window displays 'TC Equip Malf' error with one or more INOP messages and incorrect self-test readings.

Ranked causes

1. Module malfunction (common)
2. Transducer insertion wear causing intermittent microswitch (occasional)
3. Polarization or supply voltage out of range, or transducer heating malfunction (common)

First check

Module self-test readings

Test point: tcpO2 and tcpCO2 self-test numerics
Expected: tcpO2 exactly 60 mmHg (8.0 kPa); tcpCO2 exactly 40 mmHg (5.3 kPa)

5 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Invalid or expired CLEW

Message 'Invalid or Expired CLEW, See Manual' displayed; error codes 12 or 13 for BLOODANL CONFIG

Ranked causes

1. Invalid date code in V24/V26 (occasional)
2. CLEW version expired (occasional)
3. CLEW update not successfully finished (occasional)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

LEADS OFF or LEADS OFF XX or LEADS OFF (EL.X) message with INOP displayed

One or more ECG electrodes are disconnected, missing, or incorrectly attached; lead integrity check failed.

Ranked causes

1. Electrode not attached or displaced (common)
2. Wrong lead set used with EASI option enabled (occasional)
3. Lead set or ECG module defective (rare)

First check

Verify all ECG electrodes attached

Test point: Patient skin contact points (standard or EASI configuration)
Expected: All electrodes seated without air gaps

2 more checks with pass and fail actions, 5 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

LEDs on Keypad fail to work

Keypad indicator LEDs do not illuminate

Ranked causes

1. Keypad fails (common)
2. Cable, Keypad to System Board disconnected or broken (common)
3. Defective System Board (occasional)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Module not detected or transducer not connected

Parameter displayed as OFF or missing from display; no transducer detected; prompts to insert or change transducer; or site timer expired.

Ranked causes

1. No transducer connected (common)
2. Module not fully plugged in (common)
3. Site timer expired (occasional)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Module rack configuration error or LED flashing

Error message 'only 6 slots may be occupied by modules' displayed, or RIGHTMOST LED on power supply flashing continuously.

Ranked causes

1. Rack has too many parameter modules plugged in (more than 6 slots occupied) (common)
2. Faulty parameter module causing configuration error (occasional)
3. Faulty rack assembly (rare)

5 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

NBP EQUIP MALF message displayed patient safety

Hardware problem in NBP module or tubing system; pressure transducers report different values

Ranked causes

1. Faulty tubing or cuff connection (common)
2. Pressure transducer calibration drift or mismatch (occasional)
3. NBP module hardware failure (occasional)

First check

Inspect and replace tubing

Test point: NBP tubing from module to cuff connector
Expected: New tubing installed without kinks or blockages

2 more checks with pass and fail actions, 4 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

No audio alarms patient safety

Audible alarm sounds do not occur

Ranked causes

1. Speaker has failed or broken wire to speaker (common)
2. Defective Audio Circuit (common)
3. Power supply 12-volt source fails (occasional)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

SDN daughter board fault detected

Model V24 system shows fault in SDN portion when SDN Daughter Board configuration is present. Troubleshooting procedures in Chapter 3 indicate SDN circuitry problem.

Ranked causes

1. SDN Daughter Board failure (common)
2. System board failure (occasional)
3. SDN Daughter Board to System Board cables failure (occasional)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Zero and gain check verification

Perform tcpO2 zero check and tcpCO2 gain check on transducer to verify correct operation.

Ranked causes

1. Calibration unit or gases not ready (occasional)
2. Transducer unacceptable drift after Cal 1 test (occasional)
3. Cal 2 test out of range (occasional)

First check

Calibration unit function and Service mode status

Test point: Calibration unit operation and software mode
Expected: Calibration unit operational; not in Service mode

4 more checks with pass and fail actions, 4 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

BIS high impedance detected patient safety

Monitor displays BIS HIGH IMPEDANCE indicating electrode impedance above valid range

Ranked causes

1. Poor skin preparation (common)
2. PIC or DSC cable faulty (occasional)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

BIS signal quality below 15% patient safety

Monitor displays SQI < 15% indicating poor BIS waveform quality from motion, electrocautery, or sensor placement

Ranked causes

1. Sensor not properly attached to patient (common)
2. Patient motion or muscle activity (common)

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Blood Analysis parameter or results missing

Expected parameter or measurement results do not display

Ranked causes

1. Parameter not enabled in Results Selection Task Window (common)
2. Measurement not confirmed or not updated (common)

First check

Verify parameter display setting

Test point: Results Selection Task Window
Expected: Parameter switched on

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Buzzing noise in instrument

Audible buzzing or buzzing sound from instrument

Ranked causes

1. Defective Audio Circuit (common)
2. Defective Power Supply (common)

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Calibration failed or required patient safety

Calibration fails to complete or is required before transducer application; message 'tc CAL FAILED' or 'tc CAL REQUIRD' displayed.

Ranked causes

1. Out of range or unstable signal during calibration (occasional)
2. Calibration not yet performed (common)

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Cannot send data on SDN or to Central Station

Failure to transmit data on SDN; failure message displayed on Central Station

Ranked causes

1. Defective SDN circuitry (common)
2. SDN cable assembly disconnected or broken (common)

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Cartridge not inserted properly

Message 'Cartridge Not Inserted Properly' displayed; error code 47 for blood analysis failed

Ranked causes

1. Cartridge not fully inserted (common)
2. Cartridge removed after measurement started (occasional)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Contrast control does not adjust display properly

Turning contrast knob does not produce expected voltage variation or does not control display.

Ranked causes

1. Flat Panel Adapter Board is defective (common)
2. Contrast control assembly is defective (common)

First check

Attach voltmeter to test points and measure voltage while adjusting contrast knob

Test point: TP4 Flat Panel GND, TP5 VLCD
Expected: -12 to -21 volts DC (approximate) V, -12 to -21
Tools: Voltmeter

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Contrast or Brightness control knob does not adjust display

Contrast or brightness control knob fails to change display appearance or intensity

Ranked causes

1. Voltage control in Flat Panel Assembly fails (common)
2. Contrast or Brightness Control Assembly fails (common)

3 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Flat Panel display dies when AC power cord removed patient safety

Display goes blank immediately when AC power is disconnected in battery model

Ranked causes

1. Batteries not installed (common)
2. Batteries discharged (common)

First check

Check for battery presence

Test point: Battery compartment
Expected: Batteries should be present

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Module does not respond to key press

Pressing the ECG key does not bring up the task window, waveform, or numeric display on the monitor

Ranked causes

1. Plug-in module not turned ON (common)
2. System board or integral rack not communicating with module (occasional)

First check

Verify module is powered ON

Test point: Module front panel key
Expected: Module powers on when key is pressed

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

NBP CUF NOT DEFLATED message displayed patient safety

Cuff remains inflated after measurement cycle; fails to deflate properly

Ranked causes

1. Tubing blockage or cuff malfunction (occasional)
2. NBP module pneumatic control failure (occasional)

First check

Replace NBP tubing and cuff

Test point: Tubing patency and cuff condition
Expected: New tubing and cuff installed; tubing patent without blockages

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

NBP CUFF OVERPRESS message displayed patient safety

Cuff pressure exceeded normal range during inflation cycle

Ranked causes

1. Strong patient movement during inflation (common)
2. Pneumatic control defect in module (occasional)

First check

Restart measurement with patient immobilized

Test point: Patient position and movement
Expected: Patient quiet without strong movement during cuff cycle

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

NBP INTERRUPTED message displayed patient safety

Measurement interrupted due to patient movement or pump inflation/deflation timeout

Ranked causes

1. Strong patient movement during measurement (common)
2. Cuff not connected or tubing/cuff leakage (occasional)

First check

Ensure patient remains still during measurement

Test point: Patient movement observation
Expected: Patient quiet and immobilized during cuff inflation/deflation cycle

2 more checks with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

No marker pulse on screen

Marker pulse absent from ECG display

Ranked causes

1. ECG Analog Output is defective (common)
2. Defib sync input circuit is defective (common)

2 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

no Tinj transducer connected (Injectate Temperature Probe problem)

INOP message indicates Injectate Temperature Probe cable is not connected, broken, or module is faulty. Displayed when setting up or during C.O. measurement.

Ranked causes

1. Injectate Temperature Probe cable not connected or dirty connectors (common)
2. Faulty C.O. Interface Cable or module (occasional)

First check

Visually inspect Injectate Temperature Probe cable connection

Test point: Probe cable connector on C.O. Interface Cable
Expected: Cable fully seated; connectors clean and free of dirt

1 more check with pass and fail actions, 4 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

RESP LEAD OFF or RESP EQUIP MALF message displayed

Respiration measurement not functioning; RESP electrode disconnected or RESP hardware malfunction detected.

Ranked causes

1. RESP electrode not attached or patient cable unplugged (common)
2. RESP hardware malfunction (rare)

First check

Verify RESP electrode attachment and patient cable connection

Test point: RESP electrode on patient; patient cable connector on module
Expected: Electrode in contact with skin; cable fully seated in connector

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

Temperature out of range caution

BLOODANL ROOM TEMP? message displayed indicating module environment outside operating limits

Ranked causes

1. Ambient temperature outside operating range (common)
2. Blocked filter or malfunctioning ventilator fan (occasional)

First check

Verify ambient temperature

Test point: Module environment
Expected: 16 to 30°C (64 to 86°F), 16-30°C

1 more check with pass and fail actions, 2 corrective actions, and part numbers are in ServiceForge. Connect ServiceForge to your AI

"sync output not available" message displayed patient safety

Message "sync output not available" shown on screen; unable to monitor patient

Ranked causes

1. No +60V from Power Supply (common)

First check

Verify Green LED for 60 V on power supply is lit

Test point: Power supply 60V indicator LED
Expected: Green LED lit

4 corrective actions and part numbers are in ServiceForge. Connect ServiceForge to your AI

Analysis interrupted, cartridge ejected patient safety

Message 'Analysis Interrupted, Use Other Cartridge' displayed after module removal during measurement

Ranked causes

1. Module pulled from rack during measurement (occasional)

First check

Wait for locked LED indicator

Test point: Module locked LED
Expected: LED off

1 corrective action and part numbers are in ServiceForge. Connect ServiceForge to your AI

More symptoms

Battery discharges much faster than expected
Battery indicator does not appear on display
BIS impedance check in progress
BIS isoelectric EEG detected
BIS lead off or electrode disconnected
BIS signal quality below 50%
Blood Analysis module INOPS displayed
Blood Analysis Module self-test fails
Buzzing noise accompanying alarm, INOP, or QRS sound
C.O. equipment malfunction
Calibration: tcpO2/tcpCO2 chamber installation
Calibration: Temperature module
Calibration: VueLink module setup after test
Cannot reprogram time and date correctly
Cartridge error
Cartridge preburst
Cartridge type not recognized
CO2 module not plugged in
Color printing not supported
Decrease in light intensity on display
Display goes blank with Front End Link protocol problem message
Display waves are noisy or not showing smooth QRS wave
ECG EQUIP MALF message displayed
Fluid dripping or appearing below instrument
Incompatible language
Incorrect Time and Date displayed
Insufficient sample
Invalid customization data
Invalid date error
Invalid software detected
Keypad or mainframe housing discolored, cracked or deformed
Loose handles on 8-Slot Plug-in Rack
Module error - see manual
Module error or blood analysis failed
Monitor does not power on or screen blank on startup
NBP INCORRECT CUFF message displayed
NBP UNPLUGGED message displayed
New software or CLEW installed
No ECG data or waveform displayed with both defib sync and balloon pump
No numeric display when transducer unplugged from calibration chamber
Nurse-call relay not functioning
Out of sync ECG Analog Output
Patient data corrupted after power failure
Plug-in Rack falls from wall mount
Readings fluctuate excessively after calibration
Recorder Module self-test fails
Sample positioned beyond fill mark
Sample positioned short of fill mark
Speaker will not work
SVR missing CVP (no valid CVP measurement available)
Tblood no transducer (interface cable or catheter problem)
Unable to position sample
Unable to upgrade instrument using CPC Programming Tool
Uneven brightness on display
Unit does not power on
Unknown catheter (catheter, cable, or module problem)
VueLink module test procedure

57 more symptoms with ranked causes and checks are in ServiceForge. Connect ServiceForge to your AI

Error codes

Code	Meaning	Trigger	Severity
`10000–10999`	Software internal warnings	Internal software condition	info
`1000-1031`	Missing mandatory card	Required card not installed or not detected	error
`100-199`	Microprocessor interrupts due to hardware or software problem	CPU interrupt generation	critical
`1032-1063`	Wrong boot firmware	Incorrect firmware loaded at boot	error
`1064-1095`	Insufficient MPB RAM on CPU	RAM capacity insufficient for operation	error
`1096–1127`	No Extended Test result due to Hardware problem	Extended test cannot complete	error
`11`	Invalid Date, Check clock	Implausible date detected in system	error
`11000–11999`	Buffered data either lost or corrupted	Data loss or corruption detected	error
`1128–1159`	Extended Test failed	Extended test execution failure	error
`1160–1191`	RAM Card size not compatible with backplane configuration	RAM card incompatibility detected	warning
`1192–1223`	EEPROM configuration not compatible to Hardware configuration	EEPROM/Hardware mismatch	warning
`12`	Invalid or Expired CLEW, See Manual	Invalid or expired CLEW detected	error
`12000–12999`	EEPROM access failure	EEPROM read/write error	error
`1224–1255`	Wrong CPU	CPU identification failure	error
`1256–1287`	CPU is too slow	CPU speed inadequate	error
`13`	Invalid or Expired CLEW, See Manual	Invalid or expired CLEW detected	error
`13000–13999`	System internal configuration related errors	Software module structure error	error
`14`	Invalid Customization Data	Customization data is invalid	error
`18995 (4A33H)`	SDN communication problem	SDN link failure or temporary SCC power loss	error
`1-99`	Hardware test failure in first boot stage	RAM problem during boot	critical
`2`	Temperature out of range	Room temperature outside 16 to 30°C operating range	warning
`20`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`200`	MPB chip errors	Defects on CPU or other MPB participant	critical
`201-202`	System configuration problem or invalid EEPROM contents	Invalid Util CPU EEPROM data or misconfiguration	error
`20120–20128 (4E98H–4EADH)`	Data Transfer Module error	Data Transfer Module failure	error
`20300 (4F4CH)`	Rack_IF communication problem	Rack interface communication failure	error
`203-239`	MPB chip errors same as error 200	Defects on CPU or MPB participants	critical
`21`	Cartridge Preburst, Use Other Cartridge	Fluid detected on sensors prematurely during measurement	error
`21035, 21107, 24138 (522BH, 5273H, 5E4AH)`	Internal time handling problem	Time handling error	info
`2110–2152`	Unreleased Software installed (non-fatal error)	Non-released software detected	warning
`2170–3300`	Hardware problem	Hardware failure detected	critical
`22`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`22300 (571CH)`	Monitor reboots intermittently	Intermittent reboot	error
`23`	Module Error, See Manual	Module malfunction during operation	critical
`24`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`240`	Message transmission problem	System communication failure	warning
`241`	Same as errors 203-239 (MPB chip errors)	Hardware or software failure	critical
`242`	Message transmission problem	System communication failure	warning
`243-299`	Same as errors 203-239 (MPB chip errors)	Hardware or software failure	critical
`25`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`256`	Module Error, See Manual	Module malfunction during operation	critical
`257`	Module Error, See Manual	Module malfunction during operation	critical
`258`	Module Error, See Manual	Module malfunction during operation	critical
`259`	Module Error, See Manual	Module malfunction during operation	critical
`26`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`260`	Module Error, See Manual	Module malfunction during operation	critical
`261`	Module Error, See Manual	Module malfunction during operation	critical
`262`	Module Error, See Manual	Module malfunction during operation	critical
`263`	Module Error, See Manual	Module malfunction during operation	critical
`264`	Module Error, See Manual	Module malfunction during operation	critical
`265`	Module Error, See Manual	Module malfunction during operation	critical
`266`	Module Error, See Manual	Module malfunction during operation	critical
`267`	Module Error, See Manual	Module malfunction during operation	critical
`268`	Module Error, See Manual	Module malfunction during operation	critical
`269`	Module Error, See Manual	Module malfunction during operation	critical
`27`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`270`	Module Error, See Manual	Module malfunction during operation	critical
`271`	Module Error, See Manual	Module malfunction during operation	critical
`272`	Module Error, See Manual	Module malfunction during operation	critical
`273`	Module Error, See Manual	Module malfunction during operation	critical
`274`	Module Error, See Manual	Module malfunction during operation	critical
`275`	Module Error, See Manual	Module malfunction during operation	critical
`276`	Module Error, See Manual	Module malfunction during operation	critical
`277`	Module Error, See Manual	Module malfunction during operation	critical
`278`	Module Error, See Manual	Module malfunction during operation	critical
`279`	Module Error, See Manual	Module malfunction during operation	critical
`28`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`280`	Module Error, See Manual	Module malfunction during operation	critical
`281`	Module Error, See Manual	Module malfunction during operation	critical
`282`	Module Error, See Manual	Module malfunction during operation	critical
`283`	Module Error, See Manual	Module malfunction during operation	critical
`284`	Module Error, See Manual	Module malfunction during operation	critical
`285`	Module Error, See Manual	Module malfunction during operation	critical
`286`	Module Error, See Manual	Module malfunction during operation	critical
`287`	Module Error, See Manual	Module malfunction during operation	critical
`288`	Module Error, See Manual	Module malfunction during operation	critical
`289`	Module Error, See Manual	Module malfunction during operation	critical
`29`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`290`	Module Error, See Manual	Module malfunction during operation	critical
`291`	Module Error, See Manual	Module malfunction during operation	critical
`292`	Module Error, See Manual	Module malfunction during operation	critical
`293`	Module Error, See Manual	Module malfunction during operation	critical
`294`	Module Error, See Manual	Module malfunction during operation	critical
`295`	Module Error, See Manual	Module malfunction during operation	critical
`296`	Module Error, See Manual	Module malfunction during operation	critical
`297`	Incompatible Language	Language mismatch between V24/V26 and module	error
`298`	Module Error, See Manual	Module malfunction during operation	critical
`299`	Module Error, See Manual	Module malfunction during operation	critical
`3`	New Software Installed, Use Simulator	Software or CLEW recently updated	info
`30`	Sample Positioned Beyond Fill Mark	Sample level exceeds fill mark during measurement	error
`300-301`	EPROM checksum incorrect	EPROM data corruption or mismatch	error
`305-307`	Boot errors - software upgrade problem	Flash card corruption or upgrade tool issue	error
`31`	Unable to Position Sample	No sample movement detected during positioning phase	error
`310-315`	EPROM version and EEPROM version not compatible	Version mismatch between EPROM and EEPROM	error
`32`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`3212 (0C8CH)`	Out of memory	Memory exhaustion condition	critical
`33`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`330,335`	System Board does not boot up as required	Boot failure on system board	critical
`34`	Unable to Position Sample	No sample movement detected during positioning phase	error
`340,356,370`	Communication problems between APP_CPU and MPB participant	Inter-CPU communication failure	error
`35`	Sample Positioned Short of Fill Mark	Sample level below fill mark during measurement	error
`35841, 36353 (8C01H, 8E01H)`	Monitor reboots intermittently	Intermittent reboot	error
`36`	Sample Positioned Short of Fill Mark	Sample level below fill mark during measurement	error
`37`	Sample Positioned Beyond Fill Mark	Sample level exceeds fill mark during measurement	error
`3733, 11200, 20004, 20133 (0E95H, 2BC0H, 4E24H, 4EA5H)`	Internal time handling problem	Time handling error	info
`38`	Insufficient sample	Inadequate sample volume or air bubbles detected	error
`380`	Firmware revision incompatible with software revision	Version mismatch between firmware and software	error
`39`	Insufficient sample	Inadequate sample volume or air bubbles detected	error
`390`	Communication problem between CPU and MPB participant	Inter-CPU communication failure	error
`391,392`	Out of memory	Memory exhaustion on system	error
`4`	Analysis Interrupted, Use Other Cartridge	Module pulled from rack during measurement and replaced	error
`40`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`400-409`	Out of memory	Memory exhaustion on system	error
`41`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`410-419`	Missing file errors	Required files not found on system	error
`42`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`420-449`	Utility CPU / EEPROM error	Utility CPU or EEPROM hardware failure	error
`43`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`45`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`450`	VUF version incompatible with application BOOT ROM	Utility processor firmware incompatibility	error
`450`	No response from utility CPU to VUF revision request	Utility CPU communication failure	error
`46`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`46146 (B442H)`	Non-fatal error reported by the recorder module	Recorder module error condition	warning
`47`	Cartridge Not Inserted Properly	Cartridge or simulator not fully inserted into module	error
`48`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`50`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`500-699`	Software problem	Software error or corruption	error
`50497 (C541H)`	SDN communication problem	SDN link failure or temporary SCC power loss	error
`51`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`52`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`53`	Invalid Software Detected	Wrong software type detected during initialization	critical
`58`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`59`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`60`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`61`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`62`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`63`	Module Error, See Manual	Module malfunction during operation	critical
`64026 (FA1AH)`	Monitor reboots intermittently	Intermittent reboot condition	error
`65`	Module Error, See Manual	Module malfunction during operation	critical
`66`	Module Error, See Manual	Module malfunction during operation	critical
`67`	Module Error, See Manual	Module malfunction during operation	critical
`68`	Module Error, See Manual	Module malfunction during operation	critical
`69`	Cartridge Type Not Recognized	Cartridge type not compatible or module fault	error
`70`	Module Error, Use Electronic Simulator	Cartridge or simulator inserted at angle or malfunctioning	error
`700-799`	Communication problem between two CPUs	Inter-CPU communication failure	error
`72`	Module Error, See Manual	Module malfunction during operation	critical
`73`	Module Error, See Manual	Module malfunction during operation	critical
`74`	Module Error, See Manual	Module malfunction during operation	critical
`76`	Module Error, See Manual	Module malfunction during operation	critical
`77`	Module Error, See Manual	Module malfunction during operation	critical
`78`	Module Error, See Manual	Module malfunction during operation	critical
`79`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`8`	Analysis Interrupted, Use Other Cartridge	Module pulled from rack during measurement and replaced	error
`80`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`800-899`	Configuration problem	System misconfiguration	warning
`81`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`82`	Module Error, See Manual	Module malfunction during operation	critical
`85`	Module Error, See Manual	Module malfunction during operation	critical
`86`	Module Error, See Manual	Module malfunction during operation	critical
`87`	Cartridge Error, Use Other Cartridge	Cartridge or sample problem detected during analysis	warning
`89`	Module Error, See Manual	Module malfunction during operation	critical
`90`	Module Error, See Manual	Module malfunction during operation	critical
`90 (005AH)`	Internal Software problem	Software error condition	info
`900-914`	Unexpected memory change (usually RAM problem)	RAM content corruption	critical
`91`	Module Error, See Manual	Module malfunction during operation	critical
`915`	CPU failed to send test message to next CPU	Inter-CPU test communication failure	critical
`916-919`	Unexpected memory change (RAM problem)	RAM content corruption	critical
`92`	Module Error, See Manual	Module malfunction during operation	critical
`920`	Missing 32 ms interrupt on CPU	Poor connection or Util CPU failure	critical
`921-999`	Unexpected memory change (RAM problem)	RAM content corruption	critical
`93`	Module Error, See Manual	Module malfunction during operation	critical
`94`	Module Error, See Manual	Module malfunction during operation	critical
`BLOODANL CONFIG`	A configuration problem has been detected	Configuration mismatch or error	error
`BLOODANL EQU. MALF`	Permanent malfunction in the module	Module hardware failure detected	critical
`BLOODANL ROOM TEMP?`	Module environment is too warm or too cold - operating range 16 to 30°C	Ambient temperature outside safe operating range	warning
`BLOODANL UNPLUGGED`	Blood Analysis module has been unplugged from the rack	Module removed from rack interface	warning
`C.O. EQUIP MALF`	Malfunction in the C.O. hardware	Internal C.O. module or interface hardware failure detected during self-test or operation	error
`C.O. UNPLUGGED`	C.O. module is unplugged from the rack	C.O. module disconnected from module slot	error
`CUF NOT DEFLATED`	Cuff remains inflated; deflation valve stuck or blocked	Cuff pressure not released after measurement cycle completion	error
`NBP CUFF OVERPRESS`	Cuff pressure exceeded maximum during inflation	Excessive pressure generated during cuff inflation cycle	warning
`NBP EQUIP MALF`	NBP module hardware malfunction or tubing fault	Module self-test failure or transducer pressure mismatch detected	error
`NBP INCORRECT CUFF`	Cuff size setting does not match applied cuff type	Neonatal or pediatric cuff used with adult setting or vice versa	warning
`NBP INTERRUPTED`	NBP measurement cycle interrupted before completion	Patient movement during inflation/deflation or pump inflation/deflation timeout	warning
`NBP UNPLUGGED`	NBP module not detected by monitor	NBP module disconnected, unplugged, or not properly seated in rack	warning
`no Tinj transducer connected`	Injectate Temperature Probe cable is not connected, broken, or module is faulty	Injectate Temperature Probe cable missing or disconnected when entering Measure C.O. Task Window or during measurement	warning
`SVR MISSING CVP`	No valid CVP (Central Venous Pressure) available; CVP automatically set to 0 mmHg for continuous SVR calculation	CVP measurement not performed, invalid CVP value, or CVP pressure not properly labeled in monitor	warning
`Tblood NO TRANSDUC`	No C.O. Interface Cable attached to module; catheter not connected or cable broken	C.O. Interface Cable missing, disconnected, or catheter not connected during measurement setup	error
`tc CAL FAILED`	Calibration procedure failed to complete due to signal out of range or instability	Calibration attempt with unstable transducer output or out-of-range signal	error
`tc CAL REQUIRD`	Calibration required before clinical measurement; transducer not yet calibrated	Module powered on or transducer changed without completing calibration cycle	warning
`tc CAL RUNNING`	Calibration procedure is actively running	Calibration cycle initiated and in progress	info
`tc CHANGE SITE`	Site timer has expired; transducer location change needed	Site timer countdown reached zero	info
`tc CHECK TIME`	Site timer about to expire; site change needed within 15 minutes	Site timer countdown approaching zero	warning
`tc EQUIP MALF (equipment malfunction)`	Polarization voltage, supply voltage out of range, or transducer heating malfunction with transducer connected	Transducer plugged in but voltage or heating subsystem failure detected	error
`tc EQUIP MALF (module malfunction)`	Module is defective or transducer malfunction with intermittent microswitch in calibration chamber	Module hardware failure or excessive transducer insertion/removal cycles	error
`tc NO TRANSDUC`	No transducer connected to the module	Transducer connector unplugged or cable disconnected	warning
`tc STABILIZING`	Transducer has not yet reached selected temperature or skin site temperature is unstable	Temperature stabilization delay after application or insufficient site warming	info
`tc UN-PLUGGED`	Parameter is enabled but module is not fully inserted in rack	Module removed or partially seated in slot	warning
`<Tx> EQUIP MALF`	Malfunction in TEMP module hardware	Internal hardware failure detected	critical
`<Tx> NO TRANSDUC`	Temperature probe disconnected from the TEMP module	Temperature probe connector removed or unseated	error
`<Tx> OVERRANGE`	Temperature measurement out of range (below -1°C or above 45°C)	Measured temperature exceeds sensor range limits	warning
`<Tx> UNPLUGGED`	TEMP module is unplugged from the rack	TEMP module not fully seated in module rack slot	error
`Unknown catheter`	Catheter type not recognized or invalid catheter connected; values may be questionable	Unrecognized catheter inserted into C.O. Interface Cable or catheter barcode not read properly	warning

Likely causes and actions for each code are in ServiceForge. Connect ServiceForge to your AI

Community

0 fixes logged by technicians through their AI, with outcomes, for this model.

ServiceForge knowledge base record. Field-unverified unless technicians confirmed it. A teaching summary of the record, not a service manual. Export 2026-10-14.